16705-ZV4-005 Honda DIAPHRAGM (Honda Code 2795235).


16705-ZV4-005 DIAPHRAGM (Honda Code 2795235). Honda BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX DIAPHRAGM
16705-ZV4-005 DIAPHRAGM (Honda Code 2795235). Honda
Rating:
38

Buy DIAPHRAGM (Honda Code 2795235). 16705-ZV4-005 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$45.68

26-03-2025
0.25[0.11] Pounds
US: PowerToolReplacement
Honda 16705-ZV4-005 Diaphragm
Honda Honda 16705-ZV4-005 Diaphragm
Number on catalog scheme: 2
 

Honda entire parts catalog list:

BF15A1 LA 2001
BF15A1 LAS 2001
BF15A1 SA 2001
BF15A1 SAS 2001
BF15A1 XAS 2001
BF15A2 LA 2002
BF15A2 LAS 2002
BF15A2 SA 2002
BF15A2 SAS 2002
BF15A2 XAS 2002
BF15AM LA 1997
BF15AM LAS 1997
BF15AM SA 1997
BF15AM SAS 1997
BF15AM XAS 1997
BF15AW LA 1998
BF15AW LAS 1998
BF15AW SA 1998
BF15AW SAS 1998
BF15AW XAS 1998
BF15AX LA 1999
BF15AX LAS 1999
BF15AX SA 1999
BF15AX SAS 1999
BF15AX XAS 1999
BF15AY LA 2000
BF15AY LAS 2000
BF15AY SA 2000
BF15AY SAS 2000
BF15AY XAS 2000
BF9.9AM LA 1997
BF9.9AM LAS 1997
BF9.9AM SA 1997
BF9.9AM SAS 1997
BF9.9AM XA 1997
BF9.9AM XAS 1997
BF9.9AW LA 1998
BF9.9AW LAS 1998
BF9.9AW SA 1998
BF9.9AW SAS 1998
BF9.9AW XA 1998
BF9.9AW XAS 1998
BF9.9AX LA 1999
BF9.9AX LAS 1999
BF9.9AX SA 1999
BF9.9AX SAS 1999
BF9.9AX XA 1999
BF9.9AX XAS 1999
BF9.9AY LA 2000
BF9.9AY LAS 2000
BF9.9AY SA 2000
BF9.9AY SAS 2000
BF9.9AY XA 2000
BF9.9AY XAS 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Illustration 1 g02090036
Position the oil control ring with the word "TOP" in the upward position and use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If connecting rod assembly (6), the bush for piston pin (8), connecting rod cap (11), and bolts (12) or the bush for piston pin (8) is replaced, refer to Specifications, "Connecting Rods" for further information.
Illustration 2 g02513777
Illustration 3 g02514076
Illustration 4 g02514164
Aligning the connecting rod bearing in the center of the connecting rod
Lubricate the bush for piston pin (8) in connecting rod (6) with clean engine oil.
Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Place piston (4) on a suitable surface with the crown downward. Position connecting rod (6) with the forged Mark (X) to the square (13) on the piston.
Install piston pin (7) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (6). Ensure that the bearing is centralized in the connecting rod. Refer to 4.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the bearing is centralized in the connecting rod. Refer to 4.
Repeat Step 2 through Step 10 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the assembly procedure for the piston and connecting rod is completed, carry out the installation procedure as soon as possible. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Back to top