16806-ZW5-003 FLOAT (Honda Code 7206824). Honda
BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA,
FLOAT
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
BF115A2 LA
BF115A2 LCA
BF115A2 XA
BF115A2 XCA
BF115A3 LA
BF115A3 LCA
BF115A3 XA
BF115A3 XCA
BF115A4 LA
BF115A4 LCA
BF115A4 XA
BF115A4 XCA
BF115A5 LA
BF115A5 LCA
BF115A5 XA
BF115A5 XCA
BF115A6 LA
BF115A6 LCA
BF115A6 XA
BF115A6 XCA
BF115AK0 LA
BF115AK0 XA
BF130A2 LA
BF130A2 LCA
BF130A2 XA
BF130A2 XCA
BF130A3 LA
BF130A3 LCA
BF130A3 XA
BF130A3 XCA
BF130A4 LA
BF130A4 LCA
BF130A4 XA
BF130A4 XCA
Honda
Honda entire parts catalog list:
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- WATER SEPARATOR FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
- FUEL PIPE » 16806-ZW5-003
Information:
Table 1
J1939 Codes and Description Comments
3470-8
Engine Turbocharger Compressor Control : Abnormal Frequency, Pulse Width, or Period The actuator has detected an error in the Pulse Width Modulated (PWM) signal that is from the Electronic Control Module (ECM).
The code is logged.
The engine is shutdown.
5420-12
Engine Turbocharger Compressor Bypass Actuator #1 : Failure During a self-test the actuator has detected an internal fault.
The code is logged.
The engine is shutdown. Note: For a 3675-9 Engine Turbocharger Compressor Bypass Actuator Position : Abnormal Update Rate, refer to Troubleshooting , CAN Data Link - Test for information that is related to troubleshooting the data link circuitry.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A 3675-8 code is active or logged.
Proceed to Test Step 2.
Result: A 5420-12 code is active or logged.
Repair: The turbocharger compressor bypass actuator has detected an internal problem with the actuator electronics. Replace the compressor bypass actuator.
2. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 3.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Wiring for an Open Circuit
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the A-C1 and A-C2 wiring harness connectors from the ECM.
C. Disconnect the turbocharger compressor bypass actuator connector.
D. Measure the resistance between the following locations:
- Terminal 18 (PWM +) of the compressor bypass actuator connector and terminal 3 of the A-C2 ECM connector.
- Terminal 10 (PWM -) of the compressor bypass actuator connector and terminal 5 of the A-C1 ECM connector.
Open Circuit
Result: Both measurements were less than 10 ohms between the connector terminals.
Proceed to Test Step 4.
Result: One or more of the measurements were greater than 10 ohms between the connector terminals.
Repair: An open circuit has been detected. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 4.
4. Check the Wiring for a Short Circuit to Engine Ground
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the A-C1 and A-C2 wiring harness connectors from the ECM.
C. Disconnect the turbocharger compressor bypass actuator connector.
D. Measure the resistance between the following locations:
- Terminal 18 (PWM +) of the turbocharger compressor bypass actuator connector and engine ground.
- Terminal 10 (PWM -) of the turbocharger compressor bypass actuator connector and engine ground.
Short Circuit
Result: Both measurements were greater than 100 K ohms between a turbocharger compressor bypass actuator connector terminal and engine ground.
Proceed to Test Step 5.
Result: One or more of the measurements were less than 100 K ohms between a turbocharger compressor bypass actuator connector terminal and engine ground.
Repair: There is a short circuit in the wiring harness. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 5.
5. Check the Wiring for a Short Circuit
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the A-C1 and A-C2 wiring harness connectors from the ECM.
C. Disconnect the turbocharger compressor bypass actuator connector.
D. Measure the resistance between the following locations:
- Connector A-C2 terminal 3 (PWM +) and all other terminals of the ECM connector.
- Connector A-C1 terminal 5 (Digital Return) and all other terminals of the ECM connector.
Short Circuit
Result: One or more of the measurements were less than 100 K ohms between a connector terminals and any other terminal in the ECM connector.
Repair: There is a short circuit in the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts float Honda:
16013-ZW5-000
16013-ZW5-000 FLOAT SET (Honda Code 6036479).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115AX LA, BF115AX LCA, BF115AX XA, BF115AX XCA, BF115AY LA, BF115AY LCA, BF115AY XA, BF115AY XCA, BF130A1 LA, BF130A1 LCA, BF130A1 XA, BF130A1 XCA,
16013-ZY3-000
16013-ZY3-000 FLOAT SET (Honda Code 6989750).
BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA,
16906-ZZ5-003
16906-ZZ5-003 FLOAT
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA, BF40DK2 LHA, BF40DK2 LRTA, BF50DK2 LRTA, BF50DK2 XRTA, BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA