53118-ZZ3-A41 Honda GEAR, SHIFT


53118-ZZ3-A41 GEAR, SHIFT Honda BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA GEAR
53118-ZZ3-A41 GEAR, SHIFT Honda
Rating:
38

Buy GEAR, SHIFT 53118-ZZ3-A41 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$35.78
 

05-08-2022
1.0[0.45] Pounds
-: -
Honda 53118-ZZ3-A41 Gear, Shift; 53118ZZ3A41 Made by Honda
Genuine, OEM Honda Replacement Part || Honda replacement shift gear, part number 53118-ZZ3-A41
Number on catalog scheme: 37
 

Honda entire parts catalog list:

BF60AK1 LRTA 2007
BF60AK1 XRTA 2007
BFP60AK1 LRTA 2007
BFP60AK1 LRTB 2007
BFP60AK1 XRTA 2007

Information:

1. Remove the two bolts and lock to remove suction bell assembly (1) from the oil pump. 2. Remove the two bolts that hold elbow (3) to the oil pump.3. Remove bolts (2), the locks, bolts (4) and remove the oil pump. The weight of the oil pump is 35 lb. (16 kg).Install Oil Pump
1. Turn the crankshaft until the No. 1 piston is at the top center compression position. See INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR. 2. Turn both balancer shafts until the flat part on each shaft is away from the oil pan plate. Install two 3/8"-16 NC bolts (1) 1 1/2" long through the oil pan plate and into the holes in the balancer shafts. This will make the shafts so they will not turn. Do not tighten the bolts against the bottom of the holes in the shafts.3. Put the oil pump in position on the engine block and install the locks (left side only) and bolts that hold the oil pump in place. Surface (2) of the oil pump must be free of lock tabs.4. Remove bolts (1). Check to see that the balancer shaft timing is correct. The balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate, and No. 1 piston is at the top center compression position.5. Make sure the gasket is in position and install the bolts that hold elbow (3) to the oil pump.6. Put the gasket and suction bell assembly (4) in position and install the bolts and lock to hold it.end by:a) install oil panDisassemble Oil Pump
start by:a) remove oil pump
TYPICAL EXAMPLE1. Remove idler gear (2).2. Remove bearing (1) from gear (2) with tooling (B).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C). OIL PUMP Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly.6. Install gears and shafts (6) in the oil pump body assembly. 7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by:a) install oil pump


Parts gear Honda:

41131-ZW1-B01
GEAR, PINION (Honda Code 5743778).
41131-ZW1-B01 GEAR, PINION (Honda Code 5743778).
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AX LHTA, BF7
41140-ZZ3-000
GEAR, FR. BEVEL (29T)
41140-ZZ3-000 GEAR, FR. BEVEL (29T)
BF60AK1 LRTA, BF60AK1 XRTA
41151-ZZ3-000
GEAR, RR. BEVEL (29T)
41151-ZZ3-000 GEAR, RR. BEVEL (29T)
BF60AK1 LRTA, BF60AK1 XRTA
31215-ZZ3-003
GEAR, PLANET
31215-ZZ3-003 GEAR, PLANET
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
31247-ZZ3-003
GEAR ASSY. (INNER)
31247-ZZ3-003 GEAR ASSY. (INNER)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
41131-ZZ3-000
GEAR, PINION (14T)
41131-ZZ3-000 GEAR, PINION (14T)
BF60AK1 LRTA, BF60AK1 XRTA
41140-ZZ3-E00
GEAR, FR. BEVEL (28T) (POWER THRUST)
41140-ZZ3-E00 GEAR, FR. BEVEL (28T) (POWER THRUST)
BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
41151-ZZ3-E00
GEAR, RR. BEVEL (28T) (POWER THRUST)
41151-ZZ3-E00 GEAR, RR. BEVEL (28T) (POWER THRUST)
BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
Back to top