16756-ZY9-000 GROMMET, FUEL HOSE (Honda Code 9043647). Honda
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
GROMMET
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
Honda entire parts catalog list:
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
- FUEL PUMP » 16756-ZY9-000
Information:
START BY:a. remove oil pump 1. Check each connecting rod cap for its location on the crankshaft. Each cap must have a number (1) which is the same as the number on the connecting rod. Do not mix bearings.2. Turn the crankshaft until two of the pistons are at the bottom center.3. Remove connecting rod caps (2). Remove the lower bearing from the connecting rod caps.4. Push the connecting rods away from the camshaft, and remove the upper bearings.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Clean the surfaces where the bearings fit. Install the upper half of the bearing in the connecting rod. Pull the connecting rod slowly onto the crankshaft.6. Install lower half of the bearing in the cap.
When the connecting rod caps are installed, make sure that the numbers on the side of the caps are next to and in alignment with the number on the side of the connecting rods.
The serviceman must be very careful to use Plastigage correctly. The following points must be remembered.... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight, and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap, but do not remove the Plastigage. Measure the width of the Plastigage when it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specifications range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004"), the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.7. Check the bearing clearance with tool (A) as follows:a. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.b. Install the caps, tool (A) and the nuts finger tight.
Do not use an impact wrench to tighten the nuts the additional 120°.
c. Tighten each nut to a torque of 80 8 N m (60 6 lb.ft.).d. Put a mark across the nuts and bolts. Tighten the nuts 120° more.8. Remove the caps and tool (A). Make sure the connecting rod bearing caps are installed with their identification number in alignment with the connecting rod number.9. Measure the width of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066"). The maximum clearance for used bearings is 0.25 mm (.0.010").10. Install the caps. Tighten the nuts to a torque of 80 8 N m (60 6 lb.ft.). Tighten the nuts 120° more.11. Do Steps 1 through 10 for the other connecting rod bearings.END BY:a. install oil pump
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Clean the surfaces where the bearings fit. Install the upper half of the bearing in the connecting rod. Pull the connecting rod slowly onto the crankshaft.6. Install lower half of the bearing in the cap.
When the connecting rod caps are installed, make sure that the numbers on the side of the caps are next to and in alignment with the number on the side of the connecting rods.
The serviceman must be very careful to use Plastigage correctly. The following points must be remembered.... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight, and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap, but do not remove the Plastigage. Measure the width of the Plastigage when it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specifications range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004"), the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.7. Check the bearing clearance with tool (A) as follows:a. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.b. Install the caps, tool (A) and the nuts finger tight.
Do not use an impact wrench to tighten the nuts the additional 120°.
c. Tighten each nut to a torque of 80 8 N m (60 6 lb.ft.).d. Put a mark across the nuts and bolts. Tighten the nuts 120° more.8. Remove the caps and tool (A). Make sure the connecting rod bearing caps are installed with their identification number in alignment with the connecting rod number.9. Measure the width of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066"). The maximum clearance for used bearings is 0.25 mm (.0.010").10. Install the caps. Tighten the nuts to a torque of 80 8 N m (60 6 lb.ft.). Tighten the nuts 120° more.11. Do Steps 1 through 10 for the other connecting rod bearings.END BY:a. install oil pump
Parts grommet Honda:
40102-ZV5-000
40102-ZV5-000 GROMMET, CASE (LOWER) (Honda Code 3704343).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
19252-ZW1-000
19252-ZW1-000 GROMMET, WATER TUBE (Honda Code 4898193).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
40107-ZW1-700
40107-ZW1-700 GROMMET, CASE (LOWER) (C) (Honda Code 4899811).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
40204-ZW1-000
40204-ZW1-000 GROMMET, EXTENSION CASE (Honda Code 4899860).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24839-ZW1-V01
24839-ZW1-V01 GROMMET (Honda Code 4898912).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
80103-GJ5-000
80103-GJ5-000 GROMMET, ENGINE COVER (Honda Code 3376985).
BF15D3 LGA, BF15D3 LHA, BF15D3 LHGA, BF15D3 LHSA, BF15D3 LHTA, BF15D3 LRA, BF15D3 LRTA, BF15D3 SHA, BF15D3 SHGA, BF15D3 SHSA, BF15D3 SHTA, BF15D3 SRTA, BF15D3 XHA, BF15D3 XHGA, BF15D4 LGA, BF15D4 LHA, BF15D4 LHGA, BF15D4 LHSA, BF15D4 LHTA, BF15D4 LRA
37881-P2A-000
37881-P2A-000 GROMMET, TA SENSOR (Honda Code 4843074).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
91601-ZY9-000
91601-ZY9-000 GROMMET (1WAY)
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA