40108-ZW9-830 Honda GROMMET D, OIL CASE (Honda Code 6641450).

Introduction
This Special Instruction will provide instructions for installing and configuring the Product Link Bluetooth Diagnostic Adaptor.The Bluetooth Diagnostic Adaptor is a remote monitoring solution that will enable efficient and effective equipment management solutions.When installed on engines and power generation equipment and paired with the Cat Power OnSite solution mobile application, this transceiver serves as a "Bluetooth Diagnostic Adaptor". The "Bluetooth Diagnostic Adaptor" retrieves data from your equipment and transmits the data to a nearby mobile device running the Cat Power OnSite application.Important Safety Information
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe.Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or repair procedures used.
Personal injury or death can result when voiding this certification.Structural damage, an overturn, modification, alteration, or improper repair can impair the Rollover Protective Structure's (ROPS) protection capability thereby voiding this certification.Do not drill holes in the ROPS. Do not weld on the ROPS unless welding is specified in the procedure. Place welds only at the locations that are specified in the procedure.To avoid possible weakening of this ROPS, consult a Caterpillar dealer before altering this ROPS in any way. The protection offered by this ROPS will be impaired if it has been subjected to structural damage.Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification.
Improper operation of an access platform could result in injury or death. Operators must carry out their duties properly and follow all instructions and guidelines given for the machine and access platform.
Engine Specific Warnings
Do not operate or work on this engine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Turn the battery disconnect switch to the OFF position and lockout the battery disconnect switch with a safety lock.Place a Special Instruction, SEHS7332, "Do Not Operate" tag at the start switch and battery disconnect location to inform personnel that the machine is being worked on.
Generator Specific Warnings
Do not connect generator to a utility electrical distribution system unless it is isolated from the system. Electrical feedback into the distribution system can occur and could cause personal injury or death.Open and secure main distribution system switch, or if the connection is permanent, install a double throw transfer switch to prevent electrical feedback. Some generators are specifically approved by a utility to run in parallel with the distribution system and isolation may not be required. Always check with your utility as to the applicable circumstances.
Only persons with training in electrical installations must carry connections to the generator.The generator must be wired correctly. A fire or electrocution could result from wiring that is incorrect.The generator is capable of generating high voltages. Ensure that the generator is not on while the connections are being made. Follow these steps in order to prevent accidental starting:
Isolate the machine from all external loads and sources.
Shut off the Engine.
Disconnect the battery supply lines and tape the leads.
Required Parts for the Bluetooth Diagnostic Adaptor
Bluetooth Diagnostic Adaptor
Table 1
Contents of the 572-8499 Communication-Kit
Quantity Part Number Description
1 505-4280 Procedure
1 572-8500 Communication Installation Gp
1 580-6402 Power Harness As
1 590-8402 Paper
Table 2
Contents of the 572-8500 Communication Installation Gp
Quantity Part Number Description