63105-ZW4-H01ZB Honda HANDLE, TILT *NHB14M* (AQUA MARINE SILVER METARIC)


63105-ZW4-H01ZB HANDLE, TILT *NHB14M* (AQUA MARINE SILVER METARIC) Honda BF25DK3 LRGA, BF25DK3 LRTA, BF25DK3 SHGA, BF30DK3 LRGA, BF30DK3 LRTA, BF30DK3 SRTA HANDLE
63105-ZW4-H01ZB HANDLE, TILT *NHB14M* (AQUA MARINE SILVER METARIC) Honda
Rating:
43

Buy HANDLE, TILT *NHB14M* (AQUA MARINE SILVER METARIC) 63105-ZW4-H01ZB Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$114.02
 

11-09-2023
0.4188[0.19] Pounds
-: -
Honda OEM 63105-ZW4-H01ZB Handle Nhb14M
Genuine, OEM Honda Replacement Part || Honda replacement handle nhb14m, part number 63105-ZW4-H01ZB
 
$56.32
 

24-09-2017
1.50[0.45] pounds
Honda: Honda
Honda 63105-ZW4-H01ZB Handle *Nhb14M*; 63105ZW4H01ZB Made by Honda
New
Number on catalog scheme: 20
 

Honda entire parts catalog list:

BF25DK3 LRGA 2007
BF25DK3 LRTA 2007
BF25DK3 SHGA 2007
BF30DK3 LRGA 2007
BF30DK3 LRTA 2007
BF30DK3 SRTA 2007

Information:

1. Remove tube and elbow (1).2. Remove tube and oil sump (2).
Turn the crankshaft so the piston is down, and remove the ridge of carbon with emery cloth from each liner before removing the pistons. Damage can be caused to the pistons during removal by the build up of carbon if it is not removed.
3. Turn the crankshaft until the connecting rod cap to be removed is at bottom center.4. Remove connecting rod cap (3) from the connecting rod.
Put identification marks on the connecting rod caps as to their location in the engine. Keep the caps with their respective piston.
5. Push the connecting rod and piston away from the crankshaft until the piston rings are above the cylinder liner. Remove piston (4) and the connecting rod from the engine.
Use tape to hold the bearing halves together and to identify the number of the cylinder.
Install Pistons
1. Turn the crankshaft until the bearing journal for the piston to be installed is at bottom center.2. Put clean engine oil on the crankshaft journal and on the inside of the cylinder liner.3. Put clean engine oil on the piston rings and connecting rod bearings.4. Move the piston ring gaps 180° apart.5. Use tool (A), and put the piston and connecting rod in its original location in the cylinder block. Be sure the numbered side of the connecting rod is toward the right side of the engine. This is when viewed from the front of the engine.
Be sure the connecting rod bolts do not contact the crankshaft journal during installation of the piston.
6. Use a hammer handle, and lightly tap the piston into position.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to the same number on the connecting rod. The numbers must be away from the camshaft.
7. Install connecting rod cap (1) and the nuts which hold it. Tighten the nuts to a torque value of: Cadmium plated nuts (silver color) - 100 N m (75 lb.ft).Phosphated nuts (dull black color) - 130 N m (95 lb.ft.).8. Follow the same procedure for installation of the remainder of the pistons. 9. Install tube and elbow (2). Install tube and oil sump (3).End By:a. install oil panb. install cylinder head assemblyDisassemble Pistons
Start By:a. remove pistons Put identification marks on all parts for correct assembly.1. Remove rings (1) from piston (2) with tool (A). 2. Remove retaining ring (3) from each side of the piston with tool (B).3. Remove pin (4) and connecting rod (5) from piston (2). 4. Remove bolts (7) from the connecting rod.5. Remove bushing (6) from connecting rod (5) with tool group (C).6. Check all of the parts of the piston and rod for damage and wear. See Specification for minimum and maximum wear dimensions.Assemble Pistons
1. Install bolts (1) in connecting rod (2).2. Install the bushing in connecting rod (2) with tool group (A) and a press. Hone the bushing to the correct size. See Specifications for the correct dimension. 3. When the old pistons are used, clean the piston grooves with tool (B) before the rings are installed. The concave area (the part that makes the curve to the inside) in the piston is toward one side of the piston. Install the piston on the connecting rod with the concave area toward the side which has the connecting rod and cap identification on it. 4. Slide connecting rod (2) inside the piston. Install pin (3) in the piston and the connecting rod. 5. Install a retaining ring (5) on each side of piston (4) with tool (C).6. Install the top compression ring in the cylinder and measure the end gap. See Engine Specifications for the correct dimension. Measure the end gap with the compression ring at top stroke location, mid stroke location and bottom stroke location.7. Repeat the procedure for the remaining piston rings.8. Excessive end gap is an indication of cylinder liner wear. Cylinder liner replacement may be necessary.
Piston Ring Installation 9. Install rings (6) on the piston with tool (D).End By:a. install pistons


Parts handle Honda:

24811-ZW7-U01
HANDLE, REMOTE CONTROL (Honda Code 6799514).
24811-ZW7-U01 HANDLE, REMOTE CONTROL (Honda Code 6799514).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24811-ZW5-U01
HANDLE, REMOTE CONTROL (Honda Code 6799506).
24811-ZW5-U01 HANDLE, REMOTE CONTROL (Honda Code 6799506).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
68111-ZW2-F00
 
68111-ZW2-F00 HANDLE, CARRYING (Honda Code 7539141).
BF15D4 LGA, BF15D4 LHA, BF15D4 LHGA, BF15D4 LHSA, BF15D4 LHTA, BF15D4 LRA, BF15D4 LRTA, BF15D4 SHGA, BF15D4 SHTA, BF15D4 SRTA, BF15D4 XHA, BF15D4 XHGA, BF15D5 LGA, BF15D5 LHA, BF15D5 LHGA, BF15D5 LHSA, BF15D5 LHTA, BF15D5 LRA, BF15D5 LRTA, BF15D5 SHA
Back to top