06533-ZW4-H53ZA Honda HANDLEBAR KIT *NH282MU* (Honda Code 8749152). (OYSTER SILVER METALLIC-U)


06533-ZW4-H53ZA HANDLEBAR KIT *NH282MU* (Honda Code 8749152). (OYSTER SILVER METALLIC-U) Honda BF40A4 LRTA, BF40A5 LRTA, BF40A6 LRTA, BF40AK0 LRTA, BF50A4 LRTA, BF50A4 SRJA, BF50A4 XRTA, BF50A5 LRTA, BF50A5 SRJA, BF50A5 XRTA, BF50A6 LRTA, BF50A6 SRJA, BF50A6 XRTA, BF50AK0 LRTA, BF50AK0 SRJA, BF50AK0 XRTA HANDLEBAR
06533-ZW4-H53ZA HANDLEBAR KIT *NH282MU* (Honda Code 8749152). (OYSTER SILVER METALLIC-U) Honda
Rating:
83

Buy HANDLEBAR KIT *NH282MU* (Honda Code 8749152). (OYSTER SILVER METALLIC-U) 06533-ZW4-H53ZA Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$387.38
 

07-04-2018
25 Hundredths Pounds
Honda: Honda
Honda 06533-ZW4-H53ZA Handlebar Kit *Nh282
Honda 06533-ZW4-H53ZA Handlebar Kit *Nh282
Number on catalog scheme: 1
 

Honda entire parts catalog list:

BF40A4 LRTA 2004
BF40A5 LRTA 2005
BF40A6 LRTA 2006
BF40AK0 LRTA 2007
BF50A4 LRTA 2004
BF50A4 SRJA 2004
BF50A4 XRTA 2004
BF50A5 LRTA 2005
BF50A5 SRJA 2005
BF50A5 XRTA 2005
BF50A6 LRTA 2006
BF50A6 SRJA 2006
BF50A6 XRTA 2006
BF50AK0 LRTA 2007
BF50AK0 SRJA 2007
BF50AK0 XRTA 2007

Information:


TYPICAL EXAMPLE1. Turn the crankshaft until the "C" mark on crankshaft gear (1) is in alignment with the "C" mark on camshaft gear (2). To keep the engine timing correct during removal and installation of the crankshaft, put a mark on the teeth of the fuel injection pump drive gear and idler gear at location (A). Put a mark on the teeth of the idler gear and camshaft gear at location (B). The engine timing will be correct when the marks at locations (A) and (B) are in alignment and the "C" marks on the crankshaft and camshaft gears are in alignment.2. Install a 3/4" - 16 NF bolt in the gear end of the crankshaft. Install two 5/8" - 18 NF bolts in the flywheel end of the crankshaft. Fasten a hoist to the crankshaft. 3. Remove main bearings caps (3).4. Remove the crankshaft from the cylinder block. The weight of the crankshaft is 145 lb. (66.8 kg). 5. Remove main bearings (4) from the block and from the caps. Remove the thrust bearings.Install Crankshaft
1. Clean the surfaces on the cylinder block for the main bearings. Install the upper halves of the main bearings in the block. Put clean engine oil on the bearings.2. Put the crankshaft in position in the cylinder block with a hoist. Make sure all of the timing marks are in alignment.3. Clean the Nos. 1 and 5 main bearing caps. Install new bearings in caps. Put clean engine oil on bearings. Temporarily install caps to hold crankshaft in place.
Make sure part number on cap is toward front of engine, and number on bottom of cap is the same as number on cap saddle when installing caps.
4. Clean the Nos. 2, 3, and 4 main bearing caps. Install new bearings in the caps. Put clean engine oil on the bearings, bolts threads, and surfaces of the washers that contact the caps.5. Check the bearing clearance with wire (A). Install the caps and tighten the bolts to a torque of 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on each bolt head and the bearing caps. Tighten the bolts 90° more. Remove the bearing caps and measure the thickness of the wire. The main bearing clearance (wire thickness) with new bearings must be .0030 to .0059 in. (0.076 to 0.150 mm). The maximum permissible clearance with used bearings is .010 in. (0.23 mm).6. Put the caps in position on the engine and install the washers and bolts. Tighten the bolts to a torque of 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on each bolt head and the bearing caps. Tighten the bolts 90° more.7. Remove the Nos. 1 and 5 main bearing caps. Follow the procedure in Steps 4 and 5 and check the main bearing clearance for the Nos.1 and 5 main bearings.8. Follow the procedure in Step 6 and install the No. 1 main bearing cap.9. Put clean engine oil on thrust bearings (1). Install the bearings with the grooves in the bearings against the crankshaft. Install the No. 5 main bearing cap. Tighten the bolts for the cap with the procedure in Step 6.10. Check the crankshaft end play with tool group (B). The end play is controlled by the thrust bearings on the No. 5 main. The end play with new bearings must be .0025 to .0145 in. (0.064 to 0.368 mm). The maximum permissible end play with used bearings is .025 in. (0.64 mm). If a replacement has been made for any of the timing gears, it will be necessary to check the engine timing to make sure it is correct. See INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR.end by: a) install pistonsb) install timing gear coverc) install flywheel housing


Parts handlebar Honda:

06533-ZW4-H52ZA
 
06533-ZW4-H52ZA HANDLEBAR KIT *NH282MU* (Honda Code 8610966). (OYSTER SILVER METALLIC-U)
BF40A4 LRTA, BF40A5 LRTA, BF40A6 LRTA, BF40AK0 LRTA, BF50A4 LRTA, BF50A4 SRJA, BF50A4 XRTA, BF50A5 LRTA, BF50A5 SRJA, BF50A5 XRTA, BF50A6 LRTA, BF50A6 SRJA, BF50A6 XRTA, BF50AK0 LRTA, BF50AK0 SRJA, BF50AK0 XRTA
Back to top