53101-881-A00ZC Honda HANDLEBAR *NH282MU* (Honda Code 4562054). (OYSTER SILVER METALLIC-U)


53101-881-A00ZC HANDLEBAR *NH282MU* (Honda Code 4562054). (OYSTER SILVER METALLIC-U) Honda BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA HANDLEBAR
53101-881-A00ZC HANDLEBAR *NH282MU* (Honda Code 4562054). (OYSTER SILVER METALLIC-U) Honda
Rating:
58

Buy HANDLEBAR *NH282MU* (Honda Code 4562054). (OYSTER SILVER METALLIC-U) 53101-881-A00ZC Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$113.88
 

18-06-2023
0.25[0.11] Pounds
-: -
Honda 53101-881-A00ZC Handlebar *Nh282Mu*
Honda 53101-881-A00ZC Handlebar *Nh282Mu*
Number on catalog scheme: 9
 

Honda entire parts catalog list:

BF8A3 LA 2003
BF8A3 SA 2003
BF8A4 LA 2004
BF8A4 SA 2004
BF8A5 LA 2005
BF8A5 SA 2005
BF8A6 LA 2006
BF8A6 SA 2006
BF8AK0 LA 2007
BF8AK0 SA 2007
BF8AM LA 1997
BF8AM SA 1997
BF8AM XA 1997
BF8AW LA 1998
BF8AW SA 1998
BF8AW XA 1998
BF8AX LA 1999
BF8AX SA 1999
BF8AX XA 1999
BF8AY LA 2000
BF8AY SA 2000
BF8AY XA 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 138-7576 Link Bracket 2
C 6V-4876 Lubricant 1
D 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02054993
If crankshaft gear (6) was removed, install the gear on crankshaft (4).
Check the clearance of the main bearings.
Illustration 2 g02054995Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block. Coat the bearings with clean engine oil.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies. Coat the bearings with clean engine oil.
Illustration 3 g02054216Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach Tooling (B) and a suitable lifting device to crankshaft (4). For 3508 Engines, the weight of the crankshaft is approximately 400 kg (880 lb). For 3512 Engines, the weight of the crankshaft is approximately 590 kg (1300 lb). For 3516 Engines, the weight of the crankshaft is approximately 800 kg (1760 lb). Position the crankshaft in the cylinder block.
Ensure that the lower halves of the main bearings are in position in the main bearing caps. Coat the bearings with clean engine oil. Note: Main bearing caps (5) must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Illustration 4 g01049012
Coat the threads of the bolts for the main bearing caps with clean engine oil. Except for the center main bearing cap, place the main bearing caps into position. Install the bolts and washers. Tighten the bolts according to the sequence that is shown in Illustration 4. Arrow (X) points to the front of the engine. Tighten the bolts to a torque of 190 14 N m (140 10 lb ft). Then tighten the bolts for an additional 180 5 degrees (1/2 turn).
Illustration 5 g02055020
Place clean engine oil on thrust plates (3). Install thrust plates (3).
Install the center main bearing. Use the tightening procedure that is in Step 7.
Use Tooling (D) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Make sure that the upper halves of the bearings are in position on the connecting rods. Make sure that the lower halves of the bearings are in position on the connecting rod caps.
Check the clearance of the connecting rod bearings.
Position one connecting rod onto a journal of the crankshaft. Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 6 g01049104
Illustration 7 g02055042
Place Tooling (C) on the bolt threads, shanks, and seats.
Place connecting rod cap (2) into position. Install the bolts. Use the following procedure to tighten the bolts:
Tighten Bolts (A) and (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
After measuring the clearance of the connecting rod bearing, coat the bearings with clean engine oil. Use the same procedure to install the remaining connecting rod caps.
Each counterweight is numbered and must be installed in the same position as the corresponding number on the crankshaft mounting pad in order to prevent damage to the crankshaft.


Back to top