16792-ZV1-000 Honda JOINT, FUEL TUBE (Honda Code 2157006).


16792-ZV1-000 JOINT, FUEL TUBE (Honda Code 2157006). Honda BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5AY LA, BF5AY SA JOINT
16792-ZV1-000 JOINT, FUEL TUBE (Honda Code 2157006). Honda
Rating:
88

Buy JOINT, FUEL TUBE (Honda Code 2157006). 16792-ZV1-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Honda entire parts catalog list:

BF5A1 LA 2001
BF5A1 SA 2001
BF5A2 LA 2002
BF5A2 SA 2002
BF5A3 LA 2003
BF5A3 SA 2003
BF5A4 LA 2004
BF5A4 SA 2004
BF5A5 LA 2005
BF5A5 SA 2005
BF5A6 LA 2006
BF5A6 SA 2006
BF5AK0 LA 2007
BF5AK0 SA 2007
BF5AM LA 1997
BF5AM SA 1997
BF5AW LA 1998
BF5AW SA 1998
BF5AX LA 1999
BF5AX SA 1999
BF5AY LA 2000
BF5AY SA 2000

Information:

Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.Fuel Supply
Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only. If necessary, add fuel to the fuel tank. If the engine has been run out of fuel, it will be necessary to prime the fuel system. Refer to Operation and Maintenance Manual for the correct procedure.
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for debris or foreign objects which may block the fuel supply.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Air in the fuel can cause the engine to run rough. Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectors
Check fuel quality. Cold weather adversely affects the characteristics of the fuel. Refer to the engine's Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Check the filtered fuel pressure while the engine is being cranked. Refer to Systems Operation/Testing and Adjusting for the test procedure and for the correct pressure values. If the fuel pressure is low, replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details. If the fuel pressure is still low, check the operation of the fuel pressure regulating valve. Also, check for the proper operation of the fuel transfer pump.Engine Derate or Active Codes
Some engine monitoring parameters that are capable of triggering an engine derate do not produce an event code. Connect Caterpillar Electronic Technician (ET) in order to check for a derate of the engine.Certain diagnostic codes and/or event codes may cause poor performance. Use Cat ET to check for active codes and for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Note: Although a sensor's signal may be in the operational range of the sensor, the signal may not represent the actual reading. Use Cat ET to check that the pressures and the temperatures are fluctuating. Also check that the values are reasonable for the conditions that are present.Cold Mode
The Electronic Control Module (ECM) limits engine power during cold mode operation. The ECM may modify the injection timing and the ECM may cut out certain engine cylinders. This will increase startability and this will reduce warm up time. Cold mode is activated whenever the engine coolant temperature falls below a predetermined value. Cold mode remains active until the engine has warmed or a time limit is exceeded.Engine Parameters
Verify that the current flash file has been installed and then verify that the correct engine parameters are being used.Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed. If a problem is suspected with the throttle, refer to Troubleshooting, "Speed Control - Test".Electrical Connectors
Check for correct installation of the J1/P1 and J2/P2 ECM connectors and the connectors for the unit injectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to determine the performance of each cylinder. Refer to Troubleshooting, "Injector Solenoid - Test" for the proper procedure. "Turbocharger Outlet (Boost) Pressure Sensor"
Monitor the status of "Fuel Position", "Rated Fuel Limit", and "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters should agree with the following:
Table 1
"Fuel Position" = "Rated Fuel Limit"
and
"Fuel Position" < "FRC Fuel Limit" If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly.
Monitor the status of "Turbocharger Outlet (Boost) Pressure" and "Atmospheric Pressure" for normal operation on Cat ET. When the engine is not running, "Turbocharger Outlet (Boost) Pressure" should be 0 kPa (0 psi). Electronic Control Module (ECM)
If you have replaced the ECM, check the read/change system configuration parameters. Verify that the parameters match the information on the engine information plate. Verify that the correct flash file has been installed.Fuel Position Multiplier (if applicable)
If equipped, use Cat ET to verify that the fuel position multiplier is not affecting the available fuel rack. Refer to Troubleshooting, "Fuel Position Multiplier" if a problem is suspected with the input for the fuel position multiplier.Air Inlet and Exhaust System
Observe the check engine lamp. Check for an air filter restriction indicator. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting for information on inspecting the air inlet and exhaust system. Air Shutoff Valve (if applicable)
Check that the air shutoffs are open.


Parts joint Honda:

17105-ZV1-300
24312-ZV1-003
 
24312-ZV1-003 JOINT, R. SHIFT ROD (Honda Code 1984665).
BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5A
24313-ZV1-003
 
24313-ZV1-003 JOINT, L. SHIFT ROD (Honda Code 1984673).
BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5A
19271-ZV1-810
JOINT, WATER HOSE (Honda Code 2149847).
19271-ZV1-810 JOINT, WATER HOSE (Honda Code 2149847).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
17396-ZW1-000
JOINT (THREE-WAY) (Honda Code 6759229).
17396-ZW1-000 JOINT (THREE-WAY) (Honda Code 6759229).
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
Back to top