13331-ZM7-000 Honda KEY, SPECIAL (Honda Code 5988290).


13331-ZM7-000 KEY, SPECIAL (Honda Code 5988290). Honda BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB, BF2D3 SCAB, BF2D3 SCHA, BF2D3 SHA, BF2D4 LCHA, BF2D KEY
13331-ZM7-000 KEY, SPECIAL (Honda Code 5988290). Honda
Rating:
63

Buy KEY, SPECIAL (Honda Code 5988290). 13331-ZM7-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Honda entire parts catalog list:

BF2.3DK2 LCHA 2007
BF2.3DK2 SCHA 2007
BF2D1 LCHA 2001
BF2D1 SA 2001
BF2D1 SAB 2001
BF2D1 SCAB 2001
BF2D1 SCHA 2001
BF2D1 SHA 2001
BF2D2 LCHA 2002
BF2D2 SA 2002
BF2D2 SAB 2002
BF2D2 SCAB 2002
BF2D2 SCHA 2002
BF2D2 SHA 2002
BF2D3 LCHA 2003
BF2D3 SA 2003
BF2D3 SAB 2003
BF2D3 SCAB 2003
BF2D3 SCHA 2003
BF2D3 SHA 2003
BF2D4 LCHA 2004
BF2D4 SA 2004
BF2D4 SAB 2004
BF2D4 SCAB 2004
BF2D4 SCHA 2004
BF2D4 SHA 2004
BF2D5 LCHA 2005
BF2D5 SCAB 2005
BF2D5 SCHA 2005
BF2D5 SHA 2005
BF2D6 LCHA 2006
BF2D6 SCAB 2006
BF2D6 SCHA 2006
BF2D6 SHA 2006
BF2DK0 LCHA 2007
BF2DK0 SCAB 2007
BF2DK0 SCHA 2007
BF2DX LCHA 1999
BF2DX SA 1999
BF2DX SAB 1999
BF2DX SCAB 1999
BF2DX SCHA 1999
BF2DY LCHA 2000
BF2DY SA 2000
BF2DY SAB 2000
BF2DY SCAB 2000
BF2DY SCHA 2000
BF2DY SHA 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g01244067
Illustration 2 g01155119
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Use Tooling (B) to install oil control ring (3) over the spring. The word "TOP" must be upward. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If the connecting rod assembly or the bush for the piston pin have been replaced, ensure that the height grade of the connecting rod is correct. Refer to Specifications, "Connecting Rods" for further information.
Lubricate bush (7) and lubricate the bore for the piston pin in piston (4) with clean engine oil.
Illustration 3 g01244172
Place the piston on a suitable surface with the crown downward. Install connecting rod (6) and piston pin (8) to piston (4). Ensure that square boss (13) on the piston, and forged Mark (X) on the connecting rod are in the correct position. See illustration 3. Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Illustration 4 g01244068
Illustration 5 g01001160
Aligning the connecting rod bearing in the center of the connecting rod
Install the upper half of connecting rod bearing (9) to connecting rod (6). Ensure that the connecting rod bearing is centralized in the connecting rod. Refer to Illustration 5. Note: New connecting rod bearings are supplied with an alignment tool. If new connecting rod bearings are installed, use the tool to align the connecting rod bearing in the connecting rod.
Install the lower half of connecting rod bearing (10) to connecting rod cap (11). Ensure that the connecting rod bearing is centralized in the connecting rod cap. Refer to Illustration 5. Note: New connecting rod bearings are supplied with an alignment tool. If new connecting rod bearings are installed, use the tool to align the connecting rod bearing in the connecting rod cap.
Repeat Step 2 through Step 8 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the assembly procedure for the piston and connecting rod is completed, carry out the installation procedure as soon as possible.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".


Back to top