87150-ZW3-720 Honda LABEL, SPECIFICATION (NMMA) (Honda Code 4683538).


87150-ZW3-720 LABEL, SPECIFICATION (NMMA) (Honda Code 4683538). Honda BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40AW LHA, BF40AW LHTA, BF40AW LRA, BF40AW LRTA, BF40AW XRTA LABEL
87150-ZW3-720 LABEL, SPECIFICATION (NMMA) (Honda Code 4683538). Honda
Rating:
18

Buy LABEL, SPECIFICATION (NMMA) (Honda Code 4683538). 87150-ZW3-720 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Honda entire parts catalog list:

BF40A1 LHA 2001
BF40A1 LHTA 2001
BF40A1 LRA 2001
BF40A1 LRTA 2001
BF40A1 XRTA 2001
BF40A2 LHA 2002
BF40A2 LHTA 2002
BF40A2 LRA 2002
BF40A2 LRTA 2002
BF40A2 XRTA 2002
BF40A3 LHA 2003
BF40A3 LHTA 2003
BF40A3 LRA 2003
BF40A3 LRTA 2003
BF40A3 XRTA 2003
BF40AW LHA 1998
BF40AW LHTA 1998
BF40AW LRA 1998
BF40AW LRTA 1998
BF40AW XRTA 1998
BF40AX LHA 1999
BF40AX LHTA 1999
BF40AX LRA 1999
BF40AX LRTA 1999
BF40AX XRTA 1999
BF40AY LHA 2000
BF40AY LHTA 2000
BF40AY LRA 2000
BF40AY LRTA 2000
BF40AY XRTA 2000

Information:


Illustration 1 g02725693
(1) Control valve
(2) Pressure sensor
(3) Check valve
(4) Actuators
Table 1
Diagnostic Codes for Mechanical Problems or Electrical Problems with the Intake Valve Actuation System
J1939 Code CDL Code Description Conditions Which Can Cause The Code
2949-7 1922-7 Intake Valve Actuation Oil Pressure not responding This code can only occur soon after the engine has started.
This code indicates that the difference in rail pressure is incorrect while the control valve is opened and closed. The following conditions can cause this code:
A control valve that contains debris or a control valve that is not operating correctly
Damaged O-ring seal or missing O-ring seal.
2950-7 1901-7 Intake Valve Actuator #1 not responding The intake valve actuator is not responding correctly to the commands from the ECM. This can be caused by the following conditions:
There is an oil leak in the system.
There is a problem with an actuator.
The valve lash is incorrect.
The adjustment of an actuator is incorrect.
2951-7 1902-7 Intake Valve Actuator #2 not responding
2952-7 1903-7 Intake Valve Actuator #3 not responding
2953-7 1904-7 Intake Valve Actuator #4 not responding
2954-7 1905-7 Intake Valve Actuator #5 not responding
2955-7 1906-7 Intake Valve Actuator #6 not responding
2948-7 E1101 (2) Engine Intake Valve Actuation System Oil Pressure : Not Responding Properly The Engine Intake Valve Actuation System Oil Pressure did not change when the Engine Intake Valve Actuation System Oil Pressure solenoid is toggled.
2948-17 E488 (2) Engine Intake Valve Actuation System Oil Pressure : Low - moderate severity (2) The Engine Intake Valve Actuation System Oil Pressure solenoid is commanded closed, but the oil pressure does not go up.
Follow the troubleshooting procedure in order to identify the root cause of the problem. Note: Resolve any electrical problems with the system before you use this procedure.SymptomsThe following symptoms may occur if there is a problem with the intake valve actuation system.
Intermittent check engine light
Intermittent reductions in engine powerYou may need to apply a load to the engine in order to verify that the problem is resolved. The test must be performed at 75 percent of the engine's rated fuel rate for at least 30 seconds.
Table 2
Troubleshooting Test Steps Values Results
1. Check the Engine Oil Level
A. Stop the engine. Allow the engine to cool approximately 20 minutes so the oil level can stabilize.
B. Check the engine oil level.
Oil level
Result: The engine oil level is OK.
Record the engine oil level. Verify that the dipstick is calibrated correctly. Refer to Operation and Maintenance Manual, "Engine Oil Level Gauge - Calibrate".
Proceed to Test Step 2.
Result: The engine oil level is low.
Verify that the dipstick is calibrated correctly. Refer to Operation and Maintenance Manual, "Engine Oil Level Gauge - Calibrate".
Add engine oil to the proper level. Record the amount of engine oil that was added. Verify that the repair resolved the problem.
If the problem has not been eliminated, proceed to Test Step 2.
Result: The engine oil level is high.
Verify that the dipstick is calibrated correctly. Refer to Operation and Maintenance Manual, "Engine Oil Level Gauge - Calibrate".
Record the amount of engine oil that was drained. Verify that the repair resolved the problem.
If the problem has not been eliminated, proceed to Test Step 8.
Table 3
C18 Oil Pressure Table
Engine Speed Pressure (kpa) Pressure (psi)
800 233 34
1400 326 47
1800 420 61
2100 503 73
Illustration 2 g02725393
C18 oil pressure map
Table 4
Troubleshooting Test Steps Values Results
2. Check the Engine Oil Pressure
A. Turn the keyswitch OFF.
B. Establish communication between the Caterpillar Electronic Technician (ET) and the engine ECM. The communication adapter must be communicating on both data links in order to perform this procedure. Refer to Troubleshooting, "Electronic Service Tools" for more information, if necessary.
C. Install a mechanical gauge to the engine in order to read engine oil pressure. Refer to Testing and Adjusting, "Engine Oil Pressure - Test".
D. Turn the keyswitch OFF.
Oil pressure ( Refer to Table 3)
Result: The engine oil pressure is within specifications.
Proceed to Test Step 3.
Result: The engine oil pressure is low.
Record the engine oil pressure.
Record the engine rpm.
If there are any active diagnostic codes that are related to low oil pressure, refer to the appropriate topic in Troubleshooting, "Oil Pressure Is Low".
If the pressure is constant throughout the rpm range, there is a problem with the circuit for the engine oil pressure sensor. Check the wire for the pressure sensor supply (terminal A) for an open circuit.
If there are no diagnostic codes that are related to low oil pressure, refer to Testing and Adjusting, "Engine Oil Pressure - Test".
Verify that the repair resolved the problem.
Table 5
3. Determine the Logged Code
A Connect to Cat ET.
B. Turn the keyswitch ON.
C. Check for active or logged diagnostic codes:
Codes
Result


Parts label Honda:

87535-ZV5-620
LABEL, STORING CAUTION (Honda Code 3705480). (ENGLISH)
87535-ZV5-620 LABEL, STORING CAUTION (Honda Code 3705480). (ENGLISH)
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
87541-ZV5-621
LABEL, ASSIST TILT CAUTION (Honda Code 5598230). (ENGLISH)
87541-ZV5-621 LABEL, ASSIST TILT CAUTION (Honda Code 5598230). (ENGLISH)
BF15D3 LGA, BF15D3 LHGA, BF15D3 SHGA, BF15D3 XHGA, BF15D4 LGA, BF15D4 LHGA, BF15D4 SHGA, BF15D4 XHGA, BF15D5 LGA, BF15D5 LHGA, BF15D5 SHGA, BF15D5 XHGA, BF15D6 LHGA, BF15D6 SHGA, BF15D6 XHGA, BF20D3 LGA, BF20D3 LHGA, BF20D3 SHGA, BF20D3 XHGA, BF20D4
87531-ZW4-720
 
87531-ZW4-720 LABEL, OIL CAUTION (ENGLISH) (Honda Code 4683553).
BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40A4 LHA, BF40A4 LHTA, BF40A4 LRTA, BF40A5 LHA, BF40A5 LHTA
Back to top