37210-ZV1-F01 Honda LAMP ASSY., INDICATOR (Honda Code 7531734).


37210-ZV1-F01 LAMP ASSY., INDICATOR (Honda Code 7531734). Honda BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA LAMP
37210-ZV1-F01 LAMP ASSY., INDICATOR (Honda Code 7531734). Honda
Rating:
58

Buy LAMP ASSY., INDICATOR (Honda Code 7531734). 37210-ZV1-F01 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$24.03
 

27-01-2024
0.25[0.11] Pounds
US: HONDA-KTMSOUTHGA
Honda 37210-ZV1-F01 Lamp Indicator
Honda Honda 37210-ZV1-F01 Lamp Indicator
Number on catalog scheme: 18
 

Honda entire parts catalog list:

BF5A4 LA 2004
BF5A4 SA 2004
BF5A5 LA 2005
BF5A5 SA 2005
BF5A6 LA 2006
BF5A6 SA 2006
BF5AK0 LA 2007
BF5AK0 SA 2007
BF5AK2 LA 2007
BF5AK2 SA 2007
BF5AK3 LA 2007
BF5AK3 SA 2007

Information:

Probable Causes
Driven equipment
Engine supports
Low compression (cylinder pressure)
Electronic unit injectors
Individual malfunctioning cylinderRecommended Actions
Note: When performing the following procedure, do not stand near the engine. The vibration may indicate an imminent component failure.Note: Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Driven Equipment
A. Inspect the mounting bolts for the driven equipment. Inspect the alignment and the balance of the driven equipment.
B. Inspect the coupling.
Driven equipment
Result The driven equipment and the alignment are not OK.
Repair: Repair or replace the driven equipment.
Result: The driven equipment and the alignment are OK.
Proceed to Test Step 2.
2. Engine Supports
A. Inspect the mounts and the brackets while you run the engine through the speed range. Look for mounts and brackets that are loose and/or broken.
B. Check the alignment of the following before operating the engine under load for any length of time:
Mounts
Coupling
Engine supports
Result: The mounts and brackets are loose and/or broken.
Replace the mounts and brackets that are loose and/or broken.
Result: The mounts and brackets are not loose and/or broken.
Proceed to Test Step 3.
3. Clean the Fuel System
A. Following the instructions on the bottle, add Cat Fuel System Cleaner (343-6210) to the fuel tank.
Electronic Unit Injectors
Result: Performance should be restored within 2-3 hours.
Return the unit to service, the fuel system will be cleaned during operation.
Result: Performance is not restored within 2-3 hours.
Proceed to Test Step 4.
4. Low Compression (Cylinder Pressure)
A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test".
Cylinder compression
Result: The results of the compression test are outside the specifications.
Repair: Investigate the cause and rectify any faults.
Note: Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Result: The results of the compression test are OK.
Proceed to Test Step 5.
5. Electronic Unit Injectors
A. Use the electronic service tool to perform the automatic "Cylinder Cutout Test".
Note: If the compression test that was performed in Test Step 3 was satisfactory, the "Cylinder Cutout Test" will identify any faulty injectors.
Electronic Unit Injectors
Result: A faulty injector is indicated.
Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the automatic "Cylinder Cutout Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: All injectors are OK.
Proceed to Test Step 6.
6. Individual Malfunctioning Cylinders
A. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cutout Test".
As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine.
Note: If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder results in a change in the sound that is less noticeable, the cylinder may be operating below normal performance.
Cylinders
Result: The test indicates a faulty cylinder.
Repair: Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.
Result: The test indicates that all cylinders are OK.
Contact the Dealer Solutions Network (DSN).


Back to top