17845-ZY6-000 Honda LINK, THROTTLE


17845-ZY6-000 LINK, THROTTLE Honda BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4 LINK
17845-ZY6-000 LINK, THROTTLE Honda
Rating:
58

Buy LINK, THROTTLE 17845-ZY6-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Honda entire parts catalog list:

BF115DK1 LA 2007
BF115DK1 XA 2007
BF115DK1 XCA 2007
BF135A4 LA 2004
BF135A4 XA 2004
BF135A4 XCA 2004
BF135A5 LA 2005
BF135A5 XA 2005
BF135A5 XCA 2005
BF135A6 LA 2006
BF135A6 XA 2006
BF135A6 XCA 2006
BF135AK0 LA 2007
BF135AK0 XA 2007
BF135AK0 XCA 2007
BF135AK2 LA 2007
BF135AK2 XA 2007
BF135AK2 XCA 2007
BF150A4 LA 2004
BF150A4 XA 2004
BF150A4 XCA 2004
BF150A5 LA 2005
BF150A5 XA 2005
BF150A5 XCA 2005
BF150A6 LA 2006
BF150A6 XA 2006
BF150A6 XCA 2006
BF150AK0 LA 2007
BF150AK0 XA 2007
BF150AK0 XCA 2007
BF150AK2 LA 2007
BF150AK2 XA 2007
BF150AK2 XCA 2007
BF60AK1 LRTA 2007
BF60AK1 XRTA 2007
BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK0 XRTA 2007
BF90DK2 LRTA 2007
BF90DK2 XRTA 2007
BFP60AK1 LRTA 2007
BFP60AK1 LRTB 2007
BFP60AK1 XRTA 2007

Information:

start by:a) remove fuel injection pump housing and governorb) remove valve cover 1. Remove two bolts and belt tightener (1) from the timing gear cover. 2. Remove plug (3) from the timing gear cover with tool (A). Remove O-ring seal (2) from the plug. 3. Loosen nuts (5) that hold the accessory drive in position approximately .250 in. (6.35 mm). Make sure the parts on tooling are not dropped in the timing gear cover. 4. Install tool (B) in the timing gear cover as shown. Loosen the bolt that holds the gear on the accessory drive until the taper between the accessory drive and gear is broken.5. Remove tool (B). Remove the bolt and washer.6. Remove nuts (5) and accessory drive (4) from the timing gear plate.Install Accessory Drive
1. Make sure the O-ring seal is in position on the accessory drive. Install accessory drive (1) and the nuts that hold it in place.2. Install tool (A) in timing pin hole (2). Make sure tool (A) is engaged in the notch in the fuel cam of the accessory drive.3. Install the accessory drive gear, washer and bolt. Tighten the bolt finger tight. Never turn the crankshaft backward to install the bolt in the flywheel.4. Put No. 1 piston at the top center compression position (TDC) with the following procedure: a) Remove the plug from the flywheel housing. b) Turn the crankshaft clockwise (as seen from the front of the engine) until a 3/8"-16 NC bolt (3) can be installed through the timing hole in the flywheel housing and into the hole in the flywheel. 5. Check to see if both the rocker arms for the No. 1 piston can be moved backward and forward by hand. The No. 1 piston is at top center compression position when the bolt is installed in the flywheel, and both rocker arms for No. 1 piston can be moved backward and forward. If both rocker arms can not be moved, the No. 1 piston is not at the top center compression position. Remove the bolt from the flywheel. Turn the crankshaft clockwise (as seen from the front of the engine) one full turn (3604) and install the bolt again.6. Make sure the timing bolt and timing pin are in position.7. Tighten the accessory drive gear bolt to a torque of 110 5 lb.ft. (149 7 N m).8. Remove the timing pin from the accessory drive. Remove the timing bolt from the flywheel. 9. Put O-ring seal (4) in position on plug (5).10. Install plug (5) in the timing gear cover. 11. Put belt tightener (6) in position and install the bolts that hold it to the timing gear cover.12. Adjust the belt tension. See TESTING AND ADJUSTING for correct belt tension.end by:a) install fuel injection pump housing and governorb) install valve coverDisassemble Accessory Drive
start by:a) remove accessory drive 1. Remove fuel transfer pump (1). 2. Use tool (A) to remove snap ring (2). Remove O-ring seal (3). 3. Remove shaft assembly (4) from the housing. 4. Remove shaft (6) from cam (5) with tool (B) and a press. 5. Remove bearing (7) from cam (5).Assemble Accessory Drive
1. Install bearing (1) on cam (2). 2. Install shaft (3) in cam (2) with a press. 3. Put shaft assembly (4) in position in housing (5). 4. Install O-ring seal (7).5. Use tool (A) to install snap ring (6). 6. Be sure the O-ring seal is in position on fuel transfer pump (8) and put clean oil on the O-ring seal.7. Put fuel transfer pump (8) in position on the fuel pump drive and install the three nuts that hold it in place.end by:a) install accessory drive


Back to top