90301-ZY9-000 Honda NUT, HEX. (12MM) (Honda Code 8577983).


90301-ZY9-000 NUT, HEX. (12MM) (Honda Code 8577983). Honda BF75DK0 LHTA, BF75DK0 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA NUT
90301-ZY9-000 NUT, HEX. (12MM) (Honda Code 8577983). Honda
Rating:
8

Buy NUT, HEX. (12MM) (Honda Code 8577983). 90301-ZY9-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Honda entire parts catalog list:

BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK0 XRTA 2007

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - Plastigage -
C 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.Note: Ensure that the upper halves and the lower halves of the main bearings are installed so that the bearing tabs fit into the bearing tab grooves in the cylinder block and in the main bearing caps.
Illustration 1 g00503582
If the bearings were removed from the engine, clean the bearing surfaces in the cylinder block and the main bearing caps. Install the upper halves of connecting rod bearings (1) and main bearings (2).
Illustration 2 g00503642
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
Heat crankshaft gear (3) to a maximum temperature of 315 °C (600 °F). Install crankshaft gear (3) on the crankshaft.
Illustration 3 g00503668
Install Tooling (A) on the ends of the crankshaft and use a hoist to lower the crankshaft into position above the cylinder block. Align the connecting rods with the crankshaft. Align the "C" mark on crankshaft gear (3) with the "C" mark on camshaft gear (4). Lower the crankshaft into position in the cylinder block. Note: When the bearing clearance is checked and the engine is in an upright position or on the engine's side, the crankshaft must be supported against the upper halves of the main bearings. This is done in order to get a correct measurement with Tooling (B). If the crankshaft is not supported, the weight of the crankshaft will cause an incorrect reading. If the engine is not in an upright position or on the engine's side, it is not necessary to support the crankshaft. Do not rotate the crankshaft when Tooling (B) is positioned.Note: Refer to Guideline For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts" for complete details concerning the measurement of bearing clearances.
Illustration 4 g00503884
Check the main bearing clearance with Tooling (B), as follows:
Put a piece of Tooling (B) on the crankshaft journal, as shown. Note: Make sure that the part number on the main bearing cap is facing toward the front of the engine. Also, make sure that the number on the main bearing cap matches the number on the cylinder block on the left side of each main bearing cap.
Put the main bearing caps in position in the engine. Put 4C-5593 Anti-Seize Compound on the bolt threads and the face of the washers. Install the bolts and tighten the bolts to a torque of 40 4 N m (30 3 lb ft).
Put a mark on each bolt and main bearing cap. Tighten the bolts for an additional 90 degrees (1/4 turn).
Remove the main bearing caps and measure Tooling (B) in order to find the bearing clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm (0.0030 to 0.0065 inch). The maximum permissible clearance with used bearings is 0.25 mm (0.010 inch).
Illustration 5 g00503913
Put clean engine oil on thrust plate (7) for the rear main bearing. Install the new thrust plate so that the mark that is identified as the "BLOCK SIDE" faces toward the cylinder block and toward the tabs on the thrust plates in the machined area on the cylinder block. Tabs (6) will not allow thrust plate (7) to be installed backward.
Illustration 6 g00504005
Install the remaining main bearing caps. Use the same procedure that is described in Step 4b and Step 4c.
Illustration 7 g00504013
Check the crankshaft end play with Tooling (C). The end play is controlled by the thrust plates on the rear main bearing. End play with new thrust plates must be 0.122 to 0.579 mm (0.0048 to 0.0228 inch).
Illustration 8 g00504198


Parts nut Honda:

90302-921-000
NUT, HEX. (16MM) (Honda Code 0285049).
90302-921-000 NUT, HEX. (16MM) (Honda Code 0285049).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90304-ZV4-000
NUT, HEX. (6MM) (Honda Code 2800522).
90304-ZV4-000 NUT, HEX. (6MM) (Honda Code 2800522).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
94002-06490-0S
NUT, HEX. (6MM) (Honda Code 1986488).
94002-06490-0S NUT, HEX. (6MM) (Honda Code 1986488).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
94001-06490-0S
NUT, HEX. (6MM) (Honda Code 0499715).
94001-06490-0S NUT, HEX. (6MM) (Honda Code 0499715).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90301-ZW1-B00
NUT, CASTLE (18MM) (Honda Code 5743851).
90301-ZW1-B00 NUT, CASTLE (18MM) (Honda Code 5743851).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90242-ZW1-000
NUT, LOCK (64MM) (Honda Code 6994123).
90242-ZW1-000 NUT, LOCK (64MM) (Honda Code 6994123).
BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA,
90205-ZY3-000
NUT, FLANGE (8MM) (Honda Code 6994115).
90205-ZY3-000 NUT, FLANGE (8MM) (Honda Code 6994115).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
18334-MT8-770
NUT, FLANGE (5MM) (Honda Code 3355633).
18334-MT8-770 NUT, FLANGE (5MM) (Honda Code 3355633).
BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF115DK1 LA, BF115DK1 XA
Back to top