91212-ZW1-L01 Honda OIL SEAL (38X50X8) (Honda Code 6556286).


91212-ZW1-L01 OIL SEAL (38X50X8) (Honda Code 6556286). Honda BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF90A1 JHTA, BF9 OIL
91212-ZW1-L01 OIL SEAL (38X50X8) (Honda Code 6556286). Honda
Rating:
23

Buy OIL SEAL (38X50X8) (Honda Code 6556286). 91212-ZW1-L01 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$8.95

15-03-2025
0.1[0.05] Pounds
US: Mishon Corporation
NICHE Oil Seal for Honda 91212-ZW1-L01 Kawasaki 92049-2270 TCY 38x50x8mm
NICHE NICHE Seal Type TCY 38x50x8mm || NICHE Seal Replaces Honda 91212-ZW1-L01; Kawasaki 92049-2270 || Seal Inner Diameter (ID) 38mm || Seal Outer Diameter (OD) 50mm; Height 8mm || Seal Inner Diameter (ID) 38mm; Outer Diameter (OD) 50mm; Height 8mm; Material: Nitrile-Butadiene Rubber (NBR)
$24.03
 

07-11-2023
0.25[0.11] Pounds
-: -
Honda 91212-ZW1-L01 Oil Seal (38X50X8)
Honda 91212-ZW1-L01 Oil Seal (38X50X8)
Number on catalog scheme: 20
 

Honda entire parts catalog list:

BF75A1 LHTA 2001
BF75A1 LRTA 2001
BF75A1 XRTA 2001
BF75A2 LHTA 2002
BF75A2 LRTA 2002
BF75A2 XRTA 2002
BF75A3 LHTA 2003
BF75A3 LRTA 2003
BF75A3 XRTA 2003
BF75A4 LHTA 2004
BF75A4 LRTA 2004
BF75A4 XRTA 2004
BF75A5 LHTA 2005
BF75A5 LRTA 2005
BF75A5 XRTA 2005
BF75A6 LHTA 2006
BF75A6 LRTA 2006
BF75A6 XRTA 2006
BF90A1 JHTA 2001
BF90A1 JRTA 2001
BF90A1 LHTA 2001
BF90A1 LRTA 2001
BF90A1 XRTA 2001
BF90A2 JHTA 2002
BF90A2 JRTA 2002
BF90A2 LHTA 2002
BF90A2 LRTA 2002
BF90A2 XRTA 2002
BF90A3 JHTA 2003
BF90A3 JRTA 2003
BF90A3 LHTA 2003
BF90A3 LRTA 2003
BF90A3 XRTA 2003
BF90A4 JHTA 2004
BF90A4 JRTA 2004
BF90A4 LHTA 2004
BF90A4 LRTA 2004
BF90A4 XRTA 2004
BF90A5 JHTA 2005
BF90A5 JRTA 2005
BF90A5 LHTA 2005
BF90A5 LRTA 2005
BF90A5 XRTA 2005
BF90A6 JHTA 2006
BF90A6 JRTA 2006
BF90A6 LHTA 2006
BF90A6 LRTA 2006
BF90A6 XRTA 2006

Information:


Table 1
Associated Codes
E198
E390
E398
E583
107-15
107-16
157-17
5580-18
5584-0
5584-15
5584-16 Probable Causes
Codes
Parameters
Throttle Signal
Air Inlet and Exhaust System
Fuel System
Engine Load
Valve LashRecommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Engine Derate or Codes
A. Certain codes may cause poor performance. Refer to the histogram information for engine derates in Cat ET. Check for the following histograms:
1. High Exhaust Temperature Prevention Derate Time Histogram
2. High Turbo Speed Prevention Derate Time Histogram
B. If the histograms contain derates and no codes are present, then the engine is operating normally. The following list contains conditions that can cause derates:
1. Elevated altitude
2. Elevated inlet air temperature
3. Elevated ambient temperature
Engine Derate or Codes
Result: A code is not present.
Proceed to Test Step 2.
Result: A code is present.
Repair: Troubleshoot the code and then reset the histogram.
2. Check for Incorrect Parameters
A. Use Cat ET to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Parameters
Result: The parameters are correct.
Proceed to Test Step 3.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
3. Monitor the Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal
Result: The throttle signal is stable.
Proceed to Test Step 4.
Result: The throttle signal is not stable.
Repair: Make the necessary repairs. Refer to the appropriate procedure.
4. Inspect for Restrictions in the Air Inlet and Exhaust System
A. Check for an air filter restriction indicator. Replace any plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions
Result: There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 5.
Result: There are restrictions in the air inlet or exhaust system.
Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.
5. Check the Fuel System
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
E. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation. Cold mode (if applicable) is activated whenever the engine coolant temperature falls below a predetermined value. Monitor the status screen on Cat ET to verify that the engine has exited cold mode. Observe the reading for coolant temperature on the Cat ET.
Refer to "Cold Mode Operation" within the Systems Operation, "General Information".
F. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
G. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Fuel system Result: The fuel pressure is OK.
Proceed to Test Step 6.
Result: The fuel pressure is Not OK.
Repair: Replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
6. Monitor the Engine Load
A. Check accessories and parasitic loads on the engine.
Engine load Result: There is not a parasitic load.
Proceed to Test Step 7.
Result: There is a parasitic load.
Repair: Remove the parasitic load.
7. Inspect the Valve Lash
Note: The valve lash can affect the performance of the engine.
Valve lash Result: The valve lash is not set correctly.
Repair: Set the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solution Network (DSN).


Parts oil Honda:

91203-ZV5-821
OIL SEAL (Honda Code 4594784).
91203-ZV5-821 OIL SEAL (Honda Code 4594784).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91212-ZW1-005
OIL SEAL (31X46X7) (Honda Code 4901252).
91212-ZW1-005 OIL SEAL (31X46X7) (Honda Code 4901252).
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AT LHTA, BF7
91214-PL2-003
OIL SEAL (98X80X10) (NOK) (Honda Code 3056926).
91214-PL2-003 OIL SEAL (98X80X10) (NOK) (Honda Code 3056926).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
Back to top