13111-ZV5-000 Honda PIN, PISTON (Honda Code 3701182).

Table 1
Diagnostic Codes Table
J1939 Code and Description Conditions which Generate this Code System Response
4210-5 Engine Pre-lube Drive : Current Below Normal The engine Electronic Control Module (ECM) detects an open in the circuit for the prelubrication relay.
The ECM detects a short to battery voltage in the circuit for the prelubrication relay. The code is logged.
4210-6 Engine Pre-lube Drive : Current Above Normal The ECM detects a short in the circuit for the prelubrication relay. The ECM can lubricate the engine before cranking begins. This engine prelubrication is used to increase the life of certain engine parts by lubricating these parts before the starting motor is engaged.There are configuration parameters that define the operation of the prelubrication system. Prior to troubleshooting problems that are associated with the prelubrication system, check the settings of these parameters. Be sure that you understand the proper operation of the system. The status of the prelubrication system may be communicated to different controllers that are on the application. Depending on the status that is communicated there could be an effect on the engine starting. Some of these status indicators report the parameter settings of the prelubrication system. The ECM determines the charge pressure status via the engine oil pressure sensor.The prelubrication system is activated at ECM powerup. The ECM prevents the starting motor from engaging while the pump builds pressure in the lubrication system.Also, a manual prelube switch may be wired to P1-60 terminal at the primary ECM connector. When this ECM input is grounded, the ECM will activate the prelubrication relay.An override for the prelubrication system is available in Caterpillar Electronic Technician (ET). The override allows the technician to activate the prelubrication system for service and testing. The test is functional only when the engine speed is zero rpm. The test is accessed by selecting the following menus on Cat ET:
"Diagnostics"
"Diagnostic Tests"
"Override Parameters"
Illustration 1 g02974656
Schematic for the prelubrication system
Illustration 2 g01284151
Location of the terminals at the P1 ECM connector for the prelubrication system
(P1-12) Prelubrication relay
Illustration 3 g01284152
Location of the terminals at the P2 ECM connector for the prelubrication system
(P2-14) Digital return
Illustration 4 g03035987
Location of the terminals at the EL-C3 connector
(Terminal 20) Digital return
(Terminal 30) Relay
Illustration 5 g01284372
Location of the terminals at the prelubrication relay
(7) Blade terminals for the control circuit at the prelubrication relay
(8) Terminal bolts for the secondary circuit at the prelubrication relay
Illustration 6 g01155187
Locations of the terminals at the harness connector for the prelubrication relay
(Terminal 1) Prelubrication relay
(Terminal 2) Digital return
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the ECM connectors. Also, thoroughly inspect the other connectors for the prelubrication relay that are in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the proper procedure for inspecting the connectors and the wiring.
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors and the other connections that are associated with the circuit.
D. Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
E. Check the harness and the wiring for abrasion and for pinch points.
Connectors
Results: The connectors and wiring appear to be OK.
Proceed to Test Step 2
Results: There is a problem in the connectors and/or wiring.
Repair The connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
Verify that the repair eliminates the problem.
2. Check for Active Diagnostic Codes
A. Connect Cat ET to the service tool connector.
B. Restore the electrical power to the ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check the prelubrication system for an active diagnostic code.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Select diagnostic tests from Cat ET.
E. Select the "Override Parameters" screen on Cat ET.
F. Activate the override for the prelubrication system.
G. Monitor the active diagnostic code screen on Cat ET. Check the prelubrication system for an active diagnostic code.
Note: Wait at least 30 seconds in order for the diagnostic code to become active.
H. Disable the override for the prelubrication system.
Active codes
Results: No diagnostic codes are active, but a problem is suspected in the prelubrication system.
Proceed to Test Step 6
Results: A -6 diagnostic code is active at this time. A short is detected in the circuit for the prelubrication relay.
Proceed to Test Step 3
Results: A -5 diagnostic code is active at this time. An open is detected in the circuit for the prelubrication relay.
Proceed to Test Step 4
3. Create an Open Circuit at the Control Circuit of the Prelubrication Relay
A. Turn the main disconnect sw