28451-ZW1-000 Honda PULLEY, STARTER (Honda Code 4899050).


28451-ZW1-000 PULLEY, STARTER (Honda Code 4899050). Honda BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AT LHTA, BF7 PULLEY
28451-ZW1-000 PULLEY, STARTER (Honda Code 4899050). Honda
Rating:
58

Buy PULLEY, STARTER (Honda Code 4899050). 28451-ZW1-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Honda entire parts catalog list:

BF75A1 LHTA 2001
BF75A1 LRTA 2001
BF75A1 XRTA 2001
BF75A2 LHTA 2002
BF75A2 LRTA 2002
BF75A2 XRTA 2002
BF75A3 LHTA 2003
BF75A3 LRTA 2003
BF75A3 XRTA 2003
BF75A4 LHTA 2004
BF75A4 LRTA 2004
BF75A4 XRTA 2004
BF75A5 LHTA 2005
BF75A5 LRTA 2005
BF75A5 XRTA 2005
BF75A6 LHTA 2006
BF75A6 LRTA 2006
BF75A6 XRTA 2006
BF75AT LHTA 1997
BF75AT LRTA 1997
BF75AT XRTA 1997
BF75AW LHTA 1998
BF75AW LRTA 1998
BF75AW XRTA 1998
BF75AX LHTA 1999
BF75AX LRTA 1999
BF75AX XRTA 1999
BF75AY LHTA 2000
BF75AY LRTA 2000
BF75AY XRTA 2000
BF90A1 JHTA 2001
BF90A1 JRTA 2001
BF90A1 LHTA 2001
BF90A1 LRTA 2001
BF90A1 XRTA 2001
BF90A2 JHTA 2002
BF90A2 JRTA 2002
BF90A2 LHTA 2002
BF90A2 LRTA 2002
BF90A2 XRTA 2002
BF90A3 JHTA 2003
BF90A3 JRTA 2003
BF90A3 LHTA 2003
BF90A3 LRTA 2003
BF90A3 XRTA 2003
BF90A4 JHTA 2004
BF90A4 JRTA 2004
BF90A4 LHTA 2004
BF90A4 LRTA 2004
BF90A4 XRTA 2004
BF90A5 JHTA 2005
BF90A5 JRTA 2005
BF90A5 LHTA 2005
BF90A5 LRTA 2005
BF90A5 XRTA 2005
BF90A6 JHTA 2006
BF90A6 JRTA 2006
BF90A6 LHTA 2006
BF90A6 LRTA 2006
BF90A6 XRTA 2006
BF90AT LHTA 1997
BF90AT LRTA 1997
BF90AT XRTA 1997
BF90AW JHTA 1998
BF90AW JRTA 1998
BF90AW LHTA 1998
BF90AW LRTA 1998
BF90AW XRTA 1998
BF90AX JHTA 1999
BF90AX JRTA 1999
BF90AX LHTA 1999
BF90AX LRTA 1999
BF90AX XRTA 1999
BF90AY JHTA 2000
BF90AY JRTA 2000
BF90AY LHTA 2000
BF90AY LRTA 2000
BF90AY XRTA 2000

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Description Comments
3474-14 E1026 (1) Aftertreatment #1 Loss of Combustion The Aftertreatment Regeneration Device (ARD) has stopped generating heat at least four times during active high-speed regeneration.
Associated codes may indicate the system that caused the loss of combustion to occur.
The code must be cleared with the "Reset All" button on the active diagnostics screen in the electronic service tool. If active regeneration is initiated with the operator forced regeneration switch, the Engine Control Module (ECM) clears this code automatically.
3474-31 E1026 (2) Aftertreatment #1 Loss of Combustion The ARD has stopped generating heat at least four times during active regeneration.
Associated codes may indicate the system that caused the loss of combustion to occur.
The code must be cleared with the "Reset All" button on the active diagnostics screen in the electronic service tool. If active regeneration is initiated with the operator forced regeneration switch, the ECM clears this code automatically. System OperationThe combustion air system routes pressurized air from the outlet of the turbocharger compressor to the ARD. The combustion air is mixed with fuel inside the ARD. The air/fuel mixture is ignited and the air/fuel mixture is burned to provide heat for the diesel particulate filter.
Illustration 1 g06127114
Overview for the ARD combustion head
(1) Flame detection temperature sensor
(2) Electrical connection for the ARD nozzle heater
(3) ARD combustion head
(4) ARD pilot filter connector
(5) ARD spark plug
(6) Inlet for the combustion airWhen the ECM determines that the combustion air valve should be opened, the controller sends a pulse width modulated (PWM) signal to the valve. This PWM signal causes the valve to open. A position sensor located in the combustion air valve assembly then sends a signal back to the ECM showing the actual position of the valve.
Table 2
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
102-18 E1045
3480-15 or 3480-16 E1050
3480-17 or 3480-18 E1052
3487-7 E1041 (1) Complete the procedure in the order in which the steps are listed.
Table 3
Troubleshooting Test Steps Values Results
1. Check for Associated Diagnostic Trouble Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. If troubleshooting a E1026 or a 3474 code, access the "Aftertreatment Regeneration History" in the electronic service tool. Click the information tab, then click History, and then click Aftertreatment Regeneration History. If there were three successful regenerations since the code was logged, do not troubleshoot this code. Clear the code and return the unit to service.
Table 2 lists the diagnostic trouble codes that are associated with an E1026 code. Determine if any of the codes in Table 2 are present.
Diagnostic Code
Result: An associated diagnostic trouble code is not present.
Proceed to Test Step 2.
Result: An associated diagnostic trouble code is present.
Repair: Refer to Troubleshooting, "Diagnostic Trouble Codes" or Troubleshooting, "Event Codes"to troubleshoot the associated diagnostic code.
2. Check the Current Flow Through the Heater
A. Verify that the engine is off. Use a clamp-on ammeter to check the current flow through the heater.
Between 7.0 A and 14 A for a 12 V system. Or, between 3.5 A and 7 A for a 24 V system
Result: The current flow is OK.
Proceed to Test Step 3.
Result: The current flow is not between 7.0 A and 14 A for a 12 V system. The current flow is not between 3.5 A and 7 A for a 24 V system.
Repair: There may be a problem with the ARD nozzle. Refer to Troubleshooting, "ARD Nozzle Heater - Test".
3. Perform the "ARD Air System Service Test"
A. Reset all active codes and clear all logged codes. Use the electronic service tool to perform an "ARD Air System Service Test" to verify that the problem is resolved.
ARD Air System Service Test
Result: The "ARD Air System Service Test" failed.
Repair: There is a problem with the ARD combustion air system. Refer to Troubleshooting, "ARD Combustion Air - Test".
Result: The "ARD Air System Service Test" passed.
Proceed to Test Step 4.
4. Clean the Flame Detection Temperature Sensor
A. Remove flame detection temperature sensor (1).
B. Clean the flame detection temperature sensor. Use a nonmetallic cleaning pad to clean the sensor.
Flame Detection Temperature Sensor
Result: The components are clean. The flame detection temperature sensor is not damaged.
Repair: Install the flame detection sensor.
Proceed to Test Step 5.
Result: The flame detection temperature is damaged.
Repair: Replace flame detection temperature sensor.
Proceed to Test Step 5.
5. Check the ARD for Proper Operation
A. Reset all active codes and clear all logged codes. Use the electronic service tool to perform an "ARD Ignition Test" to verify that the problem is resolved.
The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, the Manual DPF Regeneration must be performed using the electronic service tool.
ARD Ignition Test
Result: The test is successful.
Proceed to Test Step 8.
Result: The test is not successful.
Proceed to Test Step 6.
6. Replace the Fitting that Contains the Filter in the ARD Head
A. Replace fitting (4) that contains the filter in the ARD head.
B. Reset all active codes and clear all logged codes by using the electronic service tool.
C. Perform the "ARD Ignition Test" using the electronic service tool. Refer to System Operation and Testing and Adjusting, "ARD Fuel System - Test".
The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, the Manual DPF Regeneration must be performed using the electronic service tool.
Filter Fittings
Result: The "ARD Ignition Test" was successful and no codes were logged.
Proceed to Test Step 8.
Result: The "ARD Ignition Test" was not successful.
Proceed to Test Step 7.
Illustration 2 g06127137


Parts pulley Honda:

13621-ZW1-003
 
13621-ZW1-003 PULLEY, TIMING BELT DRIVE (Honda Code 4897419).
BF75AT LHTA, BF75AT LRTA, BF75AT XRTA, BF75AW LHTA, BF75AW LRTA, BF75AW XRTA, BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA, BF90AT LHTA, BF90AT LRTA, BF90AT XRTA, BF90AW JHTA, BF90AW JRTA, BF90AW LHTA, BF90AW LRTA, BF9
14210-ZW1-000
 
14210-ZW1-000 PULLEY, TIMING BELT DRIVEN (Honda Code 4897435).
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AT LHTA, BF7
13621-ZW1-L01
 
13621-ZW1-L01 PULLEY, TIMING BELT DRIVE (Honda Code 6552624).
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF90A1 JHTA, BF9
Back to top