68326-ZA8-000 Honda RUBBER, SETTING (Honda Code 1788892).


68326-ZA8-000 RUBBER, SETTING (Honda Code 1788892). Honda BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX RUBBER
68326-ZA8-000 RUBBER, SETTING (Honda Code 1788892). Honda
Rating:
43

Buy RUBBER, SETTING (Honda Code 1788892). 68326-ZA8-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Honda entire parts catalog list:

BF15A1 LA 2001
BF15A1 LAS 2001
BF15A1 SA 2001
BF15A1 SAS 2001
BF15A1 XAS 2001
BF15A2 LA 2002
BF15A2 LAS 2002
BF15A2 SA 2002
BF15A2 SAS 2002
BF15A2 XAS 2002
BF15AM LA 1997
BF15AM LAS 1997
BF15AM SA 1997
BF15AM SAS 1997
BF15AM XAS 1997
BF15AW LA 1998
BF15AW LAS 1998
BF15AW SA 1998
BF15AW SAS 1998
BF15AW XAS 1998
BF15AX LA 1999
BF15AX LAS 1999
BF15AX SA 1999
BF15AX SAS 1999
BF15AX XAS 1999
BF15AY LA 2000
BF15AY LAS 2000
BF15AY SA 2000
BF15AY SAS 2000
BF15AY XAS 2000
BF9.9AM LA 1997
BF9.9AM LAS 1997
BF9.9AM SA 1997
BF9.9AM SAS 1997
BF9.9AM XA 1997
BF9.9AM XAS 1997
BF9.9AW LA 1998
BF9.9AW LAS 1998
BF9.9AW SA 1998
BF9.9AW SAS 1998
BF9.9AW XA 1998
BF9.9AW XAS 1998
BF9.9AX LA 1999
BF9.9AX LAS 1999
BF9.9AX SA 1999
BF9.9AX SAS 1999
BF9.9AX XA 1999
BF9.9AX XAS 1999
BF9.9AY LA 2000
BF9.9AY LAS 2000
BF9.9AY SA 2000
BF9.9AY SAS 2000
BF9.9AY XA 2000
BF9.9AY XAS 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 138-7576 Link Bracket 2
C 6V-4876 Lubricant -
D 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01124614
Install plugs (11) and tighten to a torque of 50 7 N m (37 5 lb ft).
Position crankshaft gear (10) on the crankshaft and install bolts (9).
Illustration 2 g01124115Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Install the upper half of main bearing (12) in the cylinder block. Ensure that the main bearing is installed so that the bearing tab fits into the notch in the cylinder block. Coat the main bearing with clean engine oil. Note: The upper half of the main bearing has an oil hole in the center.
Install the upper halves of connecting rod bearings (13) in the connecting rod assemblies. Coat the connecting rod bearing with clean engine oil.
Illustration 3 g01124538
Illustration 4 g01124192
Bolt tightening sequence for the main bearing caps
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach Tooling (B) and a suitable lifting device to each end of crankshaft (7). The weight of the 3516C crankshaft is approximately 800 kg (1765 lb). Position the crankshaft in the cylinder block.
Place clean engine oil on thrust plates (8). Install thrust plates (8) on each side of the center main bearing.
Install the lower half of the main bearing in the main bearing cap. Ensure that the main bearing is installed so that the bearing tab fits into the notch in main bearing cap (6). Coat the main bearing with clean engine oil.
Coat the underside of the bolt heads and the threads of bolts (5) with clean engine oil. Position main bearing caps (6) and install the bolts and washers. Do not tighten the bolts at this time. Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Tighten bolts (5) in sequence to a torque of 190 14 N m (140 10 lb ft).
Place an index mark on the bolts and the main bearing cap. Tighten the bolts for an additional 180 5 degrees (1/2 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Use Tooling (D) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Illustration 5 g01124522
Illustration 6 g01124419
Bolt tightening sequence for the connecting rod caps
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing on the connecting rod. Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod. Coat the connecting rod bearing with clean engine oil. Position the connecting rod onto a journal of the crankshaft.
Install the lower half of the connecting rod bearing on connecting rod cap (4). Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod cap. Coat the connecting rod bearing with clean engine oil. Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod. Install the chamfered side of the connecting rod cap next to the thrust surface of the crankshaft.Note: Reman connecting rods are not numbered for the cylinder position.
Apply Tooling (C) to the threads, the shank, and the seat of bolts (3).
Place connecting rod cap (4) into position. Install bolts (3). Use the following procedure to tighten the bolts:
Tighten Bolt (A) and Bolt (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) again to a torque of 90 5 N m (65 4 lb ft).
Place an index mark on the bolts and the connecting rod cap. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Each counterweight is numbered and must be installed in the same position as the correspondin


Parts rubber Honda:

19302-921-003
RUBBER, THERMOSTAT (Honda Code 0327866).
19302-921-003 RUBBER, THERMOSTAT (Honda Code 0327866).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
50152-ZV1-000
RUBBER A, MOUNTING (LOWER) (Honda Code 1985381).
50152-ZV1-000 RUBBER A, MOUNTING (LOWER) (Honda Code 1985381).
BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5A
50155-ZV1-000
 
50155-ZV1-000 RUBBER B, MOUNTING (LOWER) (Honda Code 1985399).
BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5A
50153-881-000
RUBBER B, SETTING (LOWER) (Honda Code 0498980).
50153-881-000 RUBBER B, SETTING (LOWER) (Honda Code 0498980).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AW LA, BF8AW SA, BF8AX LA, BF8AX SA, BF8AY LA, BF8AY SA
53165-881-010
RUBBER, GRIP (Honda Code 0958850).
53165-881-010 RUBBER, GRIP (Honda Code 0958850).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
50151-881-D70
53165-ZV4-000
RUBBER, GRIP (Honda Code 2798346).
53165-ZV4-000 RUBBER, GRIP (Honda Code 2798346).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
Back to top