16016-ZW1-L41 Honda SCREW SET (Honda Code 6552640).

Illustration 1 g00104545Attach a "Do Not Operate" warning tag to the start switch or controls before the engine is serviced or repaired. These warning tags (Special Instruction, SEHS7332) are available from your Cat dealer. Attach the warning tags to the engine and to each operator control station. When appropriate, disconnect the starting controls.Do not allow unauthorized personnel on the engine, or around the engine when the engine is being serviced.Engine exhaust contains products of combustion which may be harmful to your health. Always start the engine and operate the engine in a ventilated area. If the engine is in an enclosed area, vent the engine exhaust to the outside.Cautiously remove the following parts. To help prevent spraying or splashing of pressurized fluids, hold a rag over the part that is being removed.
Filler caps
Grease fittings
Pressure taps
Breathers
Drain plugsUse caution when cover plates are removed. Gradually loosen, but do not remove the last two bolts or nuts that are at opposite ends of the cover plate or the device. Before removing the last two bolts or nuts, pry the cover loose to relieve any spring pressure or other pressure.
Illustration 2 g00702020
Wear a hard hat, protective glasses, and other protective equipment, as required.
When work is performed around an engine that is operating, wear protective devices for ears to help prevent damage to hearing.
Do not wear loose clothing or jewelry that can snag on controls or on other parts of the engine.
Ensure that all protective guards and all covers are secured in place on the engine.
Never put maintenance fluids into glass containers. Glass containers can break.
Use all cleaning solutions with care.
Report all necessary repairs.Unless other instructions are provided, perform the maintenance under the following conditions:
The engine is stopped. Ensure that the engine cannot be started.
The protective locks or the controls are in the applied position.
Disconnect the batteries when maintenance is performed or when the electrical system is serviced. Disconnect the battery ground leads. Tape the leads to help prevent sparks.
When starting a new engine, make provisions to stop the engine if an over speed occurs. When an engine has not been started since service has been performed, make provisions to stop the engine if an over speed occurs. Shutting down the engine may be accomplished by shutting off the fuel supply and/or the air supply to the engine.
Do not attempt any repairs that are not understood. Use the proper tools. Replace any equipment that is damaged or repair the equipment.
Start the engine with the operator controls. Never short across the starting motor terminals or the batteries. This method of starting the engine could bypass the engine neutral start system and/or the electrical system could be damaged.California Proposition 65 WarningSome engine exhaust constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.Operation in a Blast Site for Product Link Radios (If Equipped)
This equipment is equipped with a Cat® Product Link communication device. When electric detonators are being used for blasting operations, radio frequency devices can cause interference with electric detonators for blasting operations which can result in serious injury or death. The Product Link communication device should be deactivated within the distance mandated under all applicable national or local regulatory requirements. In the absence of any regulatory requirements Caterpillar recommends the end user perform their own risk assessment to determine safe operating distance.
For additional information concerning Product Link, refer to the Operation and Maintenance Manual, SEBU8832.Pressurized Air and Water
Pressurized air and/or water can cause debris and/or hot water to be blown out which could result in personal injury.When pressurized air and/or pressurized water is used for cleaning, wear protective clothing, protective shoes, and eye protection. Eye protection includes goggles or a protective face shield.The maximum air pressure for cleaning purposes must be reduced to 205 kPa (30 psi) when the air nozzle is deadheaded and used with effective chip guarding (if applicable) and personal protective equipment. The maximum water pressure for cleaning purposes must be below 275 kPa (40 psi). Always wear eye protection for cleaning the cooling system.Fluid Penetration
Illustration 3 g00687600Always use a board or cardboard when you check for a leak. Leaking fluid that is under pressure can penetrate body tissue. Fluid penetration can cause serious injury and possible death. A pin hole leak can cause severe injury. If fluid is injected into your skin, you must get treatment immediately. Seek treatment from a doctor that is familiar with this type of injury.Containing Fluid Spillage
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Lines, Tubes, and Hoses
Do not bend or strike high-pressure lines. Do not install lines, tubes, or hoses that are damaged.Repair any fuel lines, oil lines, tubes, or hoses that are loose or damaged. Leaks can cause fires.Inspect all lines, tubes, and hoses carefully. Do not use bare hands to check for leaks. Always use a board or cardboard for checking engine components for leaks. Tighten all connections to the recommended torque.Check for the following conditions:
End fittings that are damaged or leaking
Outer covering that is chafed or cut
Wire that is exposed in reinforced hose
Outer covering that is ballooning locally
Flexible part of the hose that is kinked or crushed
Armoring that is embedded in the outer coveringEnsure that all the clamps, the guards, and the heat shields are installed correctly. Correct installation of these components will help to prevent these effects: vibration, rubbing against other parts and excessive heat during operation.Inhalation
Illustration 4 g02159053Exhaust
Use caution. Exhaust fumes can