14732-ZC0-000 SEE PART DETAILS - PRI; LIFTER, VALVE (Honda Code 2271278). Honda
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB
SEE
Price: query
Rating:
Honda entire parts catalog list:
- PISTON RINGS » 14732-ZC0-000
- PISTON RINGS » 14732-ZC0-000
- PISTON RINGS » 14732-ZC0-000
- PISTON RINGS » 14732-ZC0-000
- PISTON RINGS » 14732-ZC0-000
Information:
Table 1
Diagnostic Codes Table for Cooling Fan Speed
J1939 Code CDL Code Code Description Comments
1639-17 E1363 (1) Low Engine Cooling Fan Speed The code is logged. The engine cooling fan speed sensor provides a signal to the Electronic Control Module (ECM). The ECM controls fan speed by varying the current to the fan control solenoid.The engine cooling fan speed sensor receives a supply voltage from the ECM. The sensor outputs a frequency that is directly proportional to fan speed. The sensor generates a signal pulse for each revolution of the fan. The output frequency varies between 5 Hz to 180 Hz over the speed range between 50 rpm and 1800 rpm.During the following procedure, refer to the electrical schematic for the application.
Table 2
Required Tools
Tool Part Number Part Description Qty
A 351-8635 Tachometer Kit 1 Complete the procedure in the order in which the steps are listed.
Table 3
Troubleshooting Test Steps Values Results
1. Check the Status of the Engine Fan Speed
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
D. Access the "Fan Override Test" under the "Diagnostics" menu.
E. Start the "Fan Override Test" on Cat ET. Set the fan speed to 500 rpm.
F. Use Tooling (A) to determine the actual speed of the fan.
G. Compare the engine fan speed that is reported by the electronic service tool to the actual engine fan speed that is reported by Tooling (A).
H. Deactivate the "Fan Override Test".
I. Turn the keyswitch to the OFF position.
Fan Speed
Result: The engine fan speed is within 50 rpm.
The sensor is operating correctly. There may be an intermittent electrical problem in a connector or in the harness. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".
Result: The engine fan speed is not within 50 rpm.
Proceed to Test Step 2.
2. Check the Sensor Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector from the wiring harness.
C. Turn the keyswitch to the ON position.
D. Measure the sensor supply voltage between the sensor supply terminal and the sensor ground terminal on the harness connector for the sensor.
Supply Voltage
Result: The supply voltage is not reaching the sensor.
Repair: Refer to Troubleshooting, "Sensor Supply - Test".
Result: The supply voltage is reaching the sensor.
Proceed to Test Step 3.
3. Check the Signal Frequency at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Remove the sensor signal wire from the sensor connector. Connect the sensor connector.
C. Turn the keyswitch to the ON position.
D. Access the "Fan Override Test" under the "Diagnostics" menu on the electronic service tool.
E. Start the "Fan Override Test" on the electronic service tool. Set the fan speed to 800 rpm.
F. Use a multimeter to measure the frequency between the signal wire from the sensor and engine ground.
G. Deactivate the "Fan Override Test".
H. Turn the keyswitch to the OFF position.
I. Restore all connectors and wiring to the original configuration.
Sensor Frequency
Result: The frequency is approximately 80 Hz.
The engine cooling fan speed sensor is generating the correct signal.
Repair: Repair the harness or replace the harness.
Verify that the fault is resolved.
Result: The frequency is not approximately 80 Hz.
Repair: Replace the fan drive assembly.
Verify that the fault is resolved.
If the fault is still present, contact the Dealer Solutions Network (DSN).
Parts see Honda:
16957-ZE1-812
16957-ZE1-812 SEE PART DETAILS - PRI; GASKET, VALVE (Honda Code 3440708).
BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB,
93500-03006-0H
93500-03006-0H SEE PART DETAILS - PRI; SCREW, PAN (3X6) (Honda Code 0561654).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB, BF2D3 SCAB, BF2D3 SCHA, BF2D3 SHA, BF2D6 LCHA, BF2D6 SCAB, BF2D6 SCHA, BF2D6 SHA, BF2DX LCHA, BF2
95700-06012-00
95700-06012-00 SEE PART DETAILS - SUP; BOLT, FLANGE (6X12) (Honda Code 0487025).
BF2AM SA, BF5AM LA, BF5AM SA
95701-06012-00
95701-06012-00 SEE PART DETAILS - PRI; BOLT, FLANGE (6X12) (Honda Code 2105799).
BF25A1 LHA, BF25A1 LHSA, BF25A1 LRSA, BF25A1 SHA, BF25A1 SHSA, BF25A1 SRSA, BF25A1 XRSA, BF25A2 LHA, BF25A2 LHSA, BF25A2 LRSA, BF25A2 SHA, BF25A2 SHSA, BF25A2 SRSA, BF25A2 XRSA, BF25A3 LHA, BF25A3 LHSA, BF25A3 LRSA, BF25A3 SHA, BF25A3 SHSA, BF25A3 SR
96100-60000-00
96100-60000-00 SEE PART DETAILS - PRI; BEARING, RADIAL BALL (6000) (Honda Code 0671297).
BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB,
94101-06800
94101-06800 SEE PART DETAILS - PRI; WASHER, PLAIN (6MM) (Honda Code 0345900).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB
94301-08140
94301-08140 SEE PART DETAILS - PRI; PIN A, DOWEL (8X14) (Honda Code 0069310).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
96100-62030-00
96100-62030-00 SEE PART DETAILS - PRI; BEARING, RADIAL BALL (6203) (Honda Code 0722199).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY