16240-ZW0-L01 Honda SEE PART DETAILS - SUP; DIAPHRAGM ASSY. (Honda Code 6552731).


16240-ZW0-L01 SEE PART DETAILS - SUP; DIAPHRAGM ASSY. (Honda Code 6552731). Honda BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF90A2 JHTA, BF90A2 JRTA, BF90A2 LHTA, BF90A2 LRTA, BF90A2 XRTA SEE
16240-ZW0-L01 SEE PART DETAILS - SUP; DIAPHRAGM ASSY. (Honda Code 6552731). Honda
Rating:
79

Buy SEE PART DETAILS - SUP; DIAPHRAGM ASSY. (Honda Code 6552731). 16240-ZW0-L01 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Honda entire parts catalog list:

BF75A1 LHTA 2001
BF75A1 LRTA 2001
BF75A1 XRTA 2001
BF75A2 LHTA 2002
BF75A2 LRTA 2002
BF75A2 XRTA 2002
BF90A2 JHTA 2002
BF90A2 JRTA 2002
BF90A2 LHTA 2002
BF90A2 LRTA 2002
BF90A2 XRTA 2002

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
105-3
Engine Intake Manifold #1 Temperature : Voltage Above Normal 172-3
Intake Manifold Air Temperature Sensor : Voltage Above Normal The Electronic Control Module (ECM) detects that the voltage is not in the acceptable range.
The code is logged.
105-4
Engine Intake Manifold #1 Temperature : Voltage Below Normal 172-4
Intake Manifold Air Temperature Sensor : Voltage Below Normal The ECM detects that the voltage is not in the acceptable range.
The code is logged.
110-3
Engine Coolant Temperature : Voltage Above Normal 110-3
Engine Coolant Temperature : Voltage Above Normal The ECM detects that the voltage is not in the acceptable range.
The code is logged.
110-4
Engine Coolant Temperature : Voltage Below Normal 110-4
Engine Coolant Temperature : Voltage Below Normal The ECM detects that the voltage is not in the acceptable range.
The code is logged.
172-3
Engine Air Inlet Temperature : Voltage Above Normal 2526-3
Air Inlet Temperature Sensor : Voltage Above Normal The ECM detects that the voltage is not in the acceptable range.
The code is logged.
172-4
Engine Air Inlet Temperature : Voltage Below Normal 2526-4
Air Inlet Temperature Sensor : Voltage Below Normal The ECM detects that the voltage is not in the acceptable range.
The code is logged. The sensor signal for the passive sensor is routed from the Electronic Control Module (ECM) to terminal 1 of each sensor connector. The sensor return for the passive sensors is routed to the ECM from terminal 2 of each sensor connector.Diagnostics on the Cat® Electronic Technician (ET)Wiggle Test - The Wiggle Test allows you to monitor the status of the signals from the sensors.For additional information regarding the Wiggle Test, refer to the documentation that accompanies the Cat ET software.
Illustration 1 g06553324
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active.
Proceed to Test Step 2.
Result: A -4 code is active.
Proceed to Test Step 3.
Result: For a code that is logged, but not currently active.
Proceed to Test Step 4.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Terminal 1 (sensor signal) and Terminal 2 (sensor return)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Turn the keyswitch to the OFF position.
Create a Short
Result: The -3 code remains active.
Repair: There is an open in the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
3. Create an Open at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
Note: For a 110-3 code, start the engine and let the engine idle for 7 minutes. The engine must be running for at least 7 minutes in order for the diagnostic to run.
E. Turn the keyswitch to the OFF position.
Create an Open
Result: The -4 code remains active.
Repair: There is a short in the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
4. Perform the Wiggle Test
Carefully following this procedure is the best way to identify the root cause of an intermittent problem.
A. Connect Cat ET.
B. Use CAT ET to perform the following test:
- "Wiggle Test"
C. Slowly wiggle the wiring and the connectors between the P2 connector and the sensor. Slowly wiggle the wiring and the connectors between the P1 connector and the sensor. Pay particular attention to the wiring near each connector. Be sure to wiggle all the wiring.
D. As you wiggle the wiring look for the following problems:
- Loose connectors or damaged connectors
- Moisture on the connectors or the wiring
- Damage that is caused by excessive heat
- Damage that is caused by chafing
- Improper routing of wiring
- Damaged insulation
Test
Result: The wiring failed the Wiggle Test.
Repair: There is a problem with the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: The wiring passed the Wiggle Test.
Repair: The problem may be intermittent. Inspect the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.
If the wiring looks OK, perform the following procedure.
1. Turn the keyswitch to the OFF position.
2. Disconnect the connectors. Carefully inspect the terminals for proper installation. Make sure that each terminal is clean and dry.
3. Insert a pin into each socket. Verify that each socket grips the pin firmly. Repair any problems.
4. Connect all connectors.
5. Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts see Honda:

36187-ZV4-651
SEE PART DETAILS - SUP; CLIP, EMERGENCY LOCK (Honda Code 3749231).
36187-ZV4-651 SEE PART DETAILS - SUP; CLIP, EMERGENCY LOCK (Honda Code 3749231).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
17660-ZV5-A00
SEE PART DETAILS - SUP; CONNECTOR, FUEL (Honda Code 4687026).
17660-ZV5-A00 SEE PART DETAILS - SUP; CONNECTOR, FUEL (Honda Code 4687026).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115AX LA, BF115AX LCA, BF115AX XA, BF115AX XCA, BF115AY LA, BF115AY LCA, BF115AY XA, BF115AY XCA, BF130A1 LA, BF130A1 LCA, BF130A1 XA, BF130A1 XCA, BF130AX LA, BF130AX LCA, BF130AX XA, BF130AX XCA,
94301-08100
SEE PART DETAILS - PRI; PIN A, DOWEL (8X10) (Honda Code 0081711).
94301-08100 SEE PART DETAILS - PRI; PIN A, DOWEL (8X10) (Honda Code 0081711).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
87538-ZW1-740
SEE PART DETAILS - PRI; LABEL, CAUTION OPERATOR (Honda Code 4948014). (ENGLISH)
87538-ZW1-740 SEE PART DETAILS - PRI; LABEL, CAUTION OPERATOR (Honda Code 4948014). (ENGLISH)
BF15D3 LGA, BF15D3 LHA, BF15D3 LHGA, BF15D3 LHSA, BF15D3 LHTA, BF15D3 LRA, BF15D3 LRTA, BF15D3 SHA, BF15D3 SHGA, BF15D3 SHSA, BF15D3 SHTA, BF15D3 SRTA, BF15D3 XHA, BF15D3 XHGA, BF15D4 LGA, BF15D4 LHA, BF15D4 LHGA, BF15D4 LHSA, BF15D4 LHTA, BF15D4 LRA
24221-ZV4-010
SEE PART DETAILS - PRI;  SPRING, CLICK ASSIST (Honda Code 7489727).
24221-ZV4-010 SEE PART DETAILS - PRI; SPRING, CLICK ASSIST (Honda Code 7489727).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
12210-ZW1-010ZA
SEE PART DETAILS - PRI; CYLINDER HEAD *NH8* (Honda Code 6796866). (DARK GRAY)
12210-ZW1-010ZA SEE PART DETAILS - PRI; CYLINDER HEAD *NH8* (Honda Code 6796866). (DARK GRAY)
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AT LHTA, BF7
56851-ZW1-703
SEE PART DETAILS - PRI;  TANK, OIL (Honda Code 6554026).
56851-ZW1-703 SEE PART DETAILS - PRI; TANK, OIL (Honda Code 6554026).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
58130-ZW1-W23
SEE PART DETAILS - PRI; PROPELLER, THREE-BLADE (Honda Code 7786783). (13-1/2X15) (AL)
58130-ZW1-W23 SEE PART DETAILS - PRI; PROPELLER, THREE-BLADE (Honda Code 7786783). (13-1/2X15) (AL)
BF115A2 LA, BF115A2 XA, BF115A3 LA, BF115A3 XA, BF115A4 LA, BF115A4 XA, BF115A5 LA, BF115A5 XA, BF115A6 LA, BF115A6 XA, BF115AK0 LA, BF115AK0 XA, BF130A2 LA, BF130A2 XA, BF130A3 LA, BF130A3 XA, BF130A4 LA, BF130A4 XA, BF75A1 LHTA, BF75A1 LRTA, BF75A1
Back to top