16473-PD6-000 Honda SEE PART DETAILS - SUP; RUBBER RING, INJECTOR (Honda Code 1855576).


16473-PD6-000 SEE PART DETAILS - SUP; RUBBER RING, INJECTOR (Honda Code 1855576). Honda BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, SEE
16473-PD6-000 SEE PART DETAILS - SUP; RUBBER RING, INJECTOR (Honda Code 1855576). Honda
Rating:
18

Buy SEE PART DETAILS - SUP; RUBBER RING, INJECTOR (Honda Code 1855576). 16473-PD6-000 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$3.49
 

16-06-2023

-: -
Honda 16473-PD6-000 Cushion Ring
Genuine Honda part that fits your specific vehicle || Cushion Ring || Part Number: 16473-PD6-000 || Manufactured to meet specifications for fit, form, and function
Number on catalog scheme: 4
 

Honda entire parts catalog list:

BF115A1 LA 2001
BF115A1 LCA 2001
BF115A1 XA 2001
BF115A1 XCA 2001
BF115A2 LA 2002
BF115A2 LCA 2002
BF115A2 XA 2002
BF115A2 XCA 2002
BF115A3 LA 2003
BF115A3 LCA 2003
BF115A3 XA 2003
BF115A3 XCA 2003
BF115A4 LA 2004
BF115A4 LCA 2004
BF115A4 XA 2004
BF115A4 XCA 2004
BF115A5 LA 2005
BF115A5 LCA 2005
BF115A5 XA 2005
BF115A5 XCA 2005
BF115A6 LA 2006
BF115A6 LCA 2006
BF115A6 XA 2006
BF115A6 XCA 2006
BF115AK0 LA 2007
BF115AK0 XA 2007
BF115AX LA 1999
BF115AX LCA 1999
BF115AX XA 1999
BF115AX XCA 1999
BF115AY LA 2000
BF115AY LCA 2000
BF115AY XA 2000
BF115AY XCA 2000
BF130A1 LA 2001
BF130A1 LCA 2001
BF130A1 XA 2001
BF130A1 XCA 2001
BF130A2 LA 2002
BF130A2 LCA 2002
BF130A2 XA 2002
BF130A2 XCA 2002
BF130A3 LA 2003
BF130A3 LCA 2003
BF130A3 XA 2003
BF130A3 XCA 2003
BF130A4 LA 2004
BF130A4 LCA 2004
BF130A4 XA 2004
BF130A4 XCA 2004
BF130AX LA 1999
BF130AX LCA 1999
BF130AX XA 1999
BF130AX XCA 1999
BF130AY LA 2000
BF130AY LCA 2000
BF130AY XA 2000
BF130AY XCA 2000

Information:


Table 1
Diagnostic Codes Table for Sensor Calibration
J1939 Code Code Description Comments
411-13 Engine Exhaust Gas Recirculation Differential Pressure : Out of Calibration The ECM detects the following conditions:
The NRS differential pressure is outside the acceptable range during initialization check, or during sensor calibration when the engine is not running.
The warning lamp will come on and the engine will be derated.
The code is logged.
3251–13 Aftertreatment #1 DPF Differential Pressure : Out of Calibration The ECM detects the following conditions:
The Diesel Particulate Filter (DPF) differential pressure is outside the acceptable range during initialization check, or during sensor calibration when the engine is not running.
The warning lamp will come on and the engine will derate. The code is logged.
3358-13 Engine Exhaust Gas Recirculation Inlet Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the NRS inlet pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the NRS inlet pressure and the barometric pressure is outside the acceptable range during sensor calibration when the engine is not running.
The warning lamp will come on and the engine will derate. The code is logged.
3563-13 Engine Intake Manifold #1 Absolute Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the intake manifold air pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the intake manifold air pressure and the barometric pressure is outside the acceptable range during sensor calibration with the engine not running.
The warning lamp will come on and the engine will derate.
The code is logged.
3609–13 DPF #1 Intake Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the DPF inlet pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the DPF inlet pressure and the barometric pressure is outside the acceptable range during sensor calibration with the engine not running.
The warning lamp will come on and the engine will derate.
The code is logged.
Table 2
Troubleshooting Test Steps Values Results
1. Check For Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
D. Use the electronic service tool to check that coolant temperature, intake manifold air temperature, and NRS temperature are all at least 5° C (41° F).
Note: Wait at least 10 seconds in order for the diagnostic codes to become active.
E. Use the electronic service tool to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -3 or -4 codes for the pressure sensor or the barometric pressure sensor.
F. Use the electronic service tool to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -13 code for a pressure sensor or the barometric pressure sensor.
G. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the pressure sensors.
Repair: If there are logged diagnostic codes for the intake manifold pressure sensor, the fault may be intermittent.
Refer to Troubleshooting, "Electrical Connectors - Inspect" to identify intermittent faults.
Result: One or more of the temperature sensors is reading less than 5° C (41° F).
Proceed to Test Step 2.
Result: There is an active -3 or -4 diagnostic code for a pressure sensor or the barometric pressure sensor.
Repair: Troubleshoot these codes before continuing with this procedure.
Result: There are multiple -13 diagnostic codes active.
Proceed to Test Step 3.
Result: There is an active -13 diagnostic code for only one sensor.
Proceed to Test Step 4.
2. Ensure that the Systems are Fully Thawed
A. Move the machine into an environment where the ambient temperature is greater than 5° C (41° F) during any troubleshooting.
B. If engine has been operated or stored in cold ambient conditions where there is a risk of ice formation on a sensor or sensor pipes, run engine until the coolant temperature exceeds 65° C (149° F) for 20 minutes.
C. Turn the keyswitch to the OFF position. Wait for at least 20 seconds. The electronic service tool will disconnect.
D. Turn the keyswitch to the ON position.
E. Verify that coolant temperature, intake manifold air temperature, and NRS temperature are all now at least 5° C (41° F).
F. Check for active -13 diagnostic codes.
G. Check that the suspect sensor is installed correctly. Check that the suspect sensor is fully seated into the engine.
Diagnostic codes
Result: There are no active -13 codes.
Repair: The fault was caused by ice in the system that has now been thawed. Return the unit to service
Result: There are multiple -13 diagnostic codes active.
Proceed to Test Step 3.
Result: A single -13 code is active or logged.
Proceed to Test Step 4.
3. Check the Barometric Pressure Sensor
A. Turn the keyswitch to the OFF position.
B. Install a new Electronic Control Module (ECM).
Note: The Barometric Pressure Sensor is located within the ECM so cannot be replaced separately. To replace the Barometric Pressure Sensor, the ECM must be replaced.
C. Turn the keyswitch to the ON position. Do not start the engine.
Note: Wait at least 10 seconds in order for the diagnostic codes to become active.
D. Monitor the status parameter for the suspect sensor on the electronic service tool.
Barometric pressure sensor fault
Result: There is no active -13 code. The fault was caused by a faulty barometric pressure sensor.
Use the electronic service tool to clear all logged codes. Return the unit to service.
Result: A -13 code is active.
Proceed to Test Step 4.
4. Check the Suspect Pressure Sensor
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect sensor and remove the sensor from the engine.
C. Check the sensor for a blockage.
D. Temporarily reconnect the sensor to the harness. Do not install the sensor on the engine.
E. Turn the keyswitch to the ON position. Do not start the engine.
F. Check for an active -13 diagnostic code for the suspect sensor.
Barometric pressure sensor fault
Result: There is an active -13 code or the sensor is blocked
Temporarily connect a new sensor to the harness. Use the electronic service tool to confirm that the repair eliminates the fault.
If the fault


Parts see Honda:

16957-ZE1-812
SEE PART DETAILS - PRI;   GASKET, VALVE (Honda Code 3440708).
16957-ZE1-812 SEE PART DETAILS - PRI; GASKET, VALVE (Honda Code 3440708).
BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB,
94101-06800
90014-ZV1-010
SEE PART DETAILS - PRI; BOLT, FLANGE (5X22) (Honda Code 7496573).
90014-ZV1-010 SEE PART DETAILS - PRI; BOLT, FLANGE (5X22) (Honda Code 7496573).
BF15A1 LA, BF15A1 SA, BF15A2 LA, BF15A2 SA, BF15AM LA, BF15AM SA, BF15AW LA, BF15AW SA, BF15AX LA, BF15AX SA, BF15AY LA, BF15AY SA, BF25A1 LHA, BF25A1 SHA, BF25A2 LHA, BF25A2 SHA, BF25A3 LHA, BF25A3 SHA, BF25D4 LHA, BF25D4 SHA, BF25D5 LHA, BF25D5 SHA
87121-ZV1-C00
19210-881-A01
SEE PART DETAILS - SUP; IMPELLER, PUMP (Honda Code 3739604).
19210-881-A01 SEE PART DETAILS - SUP; IMPELLER, PUMP (Honda Code 3739604).
BF5AM LA, BF5AM SA, BF5AX LA, BF5AX SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AX LA, BF8AX SA, BF8AX XA
90014-ZV1-000
SEE PART DETAILS - SUP; BOLT, FLANGE (5X22) (Honda Code 1986090).
90014-ZV1-000 SEE PART DETAILS - SUP; BOLT, FLANGE (5X22) (Honda Code 1986090).
BF15A1 LA, BF15A1 SA, BF15A2 LA, BF15A2 SA, BF15AM LA, BF15AM SA, BF15AW LA, BF15AW SA, BF15AX LA, BF15AX SA, BF15AY LA, BF15AY SA, BF25A1 LHA, BF25A1 SHA, BF25A2 LHA, BF25A2 SHA, BF25A3 LHA, BF25A3 SHA, BF25AW LHA, BF25AW SHA, BF25AX LHA, BF25AX SHA
92101-06016-0B
SEE PART DETAILS - PRI;  BOLT, HEX. (6X16) (Honda Code 2801181).
92101-06016-0B SEE PART DETAILS - PRI; BOLT, HEX. (6X16) (Honda Code 2801181).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
Back to top