31650-881-A02 Honda SEE PART DETAILS - PRI; RECEPTACLE ASSY., CHARGE (Honda Code 7536261).


31650-881-A02 SEE PART DETAILS - PRI; RECEPTACLE ASSY., CHARGE (Honda Code 7536261). Honda BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA SEE
31650-881-A02 SEE PART DETAILS - PRI; RECEPTACLE ASSY., CHARGE (Honda Code 7536261). Honda
Rating:
8

Buy SEE PART DETAILS - PRI; RECEPTACLE ASSY., CHARGE (Honda Code 7536261). 31650-881-A02 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Honda entire parts catalog list:

BF8A4 LA 2004
BF8A4 SA 2004
BF8A5 LA 2005
BF8A5 SA 2005
BF8A6 LA 2006
BF8A6 SA 2006
BF8AK0 LA 2007
BF8AK0 SA 2007
BF8AM LA 1997
BF8AM SA 1997
BF8AM XA 1997
BF8AW LA 1998
BF8AW SA 1998
BF8AW XA 1998

Information:


Table 1
J1939 Code and Descriptions CDL Code and Descriptions Comments
626-5
Engine Start Enable Device 1 : Current Below Normal 2417-5
Ether Injection Control Solenoid : Current Below Normal The code is latched. The code is logged.
Ether injection is disabled.
626-6
Engine Start Enable Device 1 : Current Above Normal 2417-6
Ether Injection Control Solenoid : Current Above Normal The code is latched. The code is logged.
Ether injection is disabled. The ether injection system will improve cold weather starting of the engine. The engine Electronic Control Module (ECM) controls the ether injection system. The ether injection system is disabled if there is an active engine shutdown.Activation of the ether starting aid is based from a map using the coolant temperature, intake manifold temperature, and atmospheric pressure. Refer to Illustration 1.
Illustration 1 g02445796The following conditions must be met for the ether injection system to be enabled:
Ether injection is set to enabled in Cat® Electronic Technician (ET)
Engine coolant temperature is less than the "Start Aid Selection Temperature - Coolant". Refer to Illustration 1.
Intake manifold temperature is less than the "Start Aid Selection Temperature - IMAT."
Coolant temperature and intake manifold air temperature are within 11° C of each other.
Illustration 2 g01696575
Ether starting aid group
(1) Ether injection solenoid
Breathing ether vapors or repeated contact of ether with skin can cause personal injury. Personal injury may occur from failure to adhere to the following procedures.Use ether only in well ventilated areas.Do not smoke while changing ether cylinders.Use ether with care to avoid fires.Do not store replacement ether cylinders in living areas or in the operator's compartment.Do not store ether cylinders in direct sunlight or at temperatures above 49 °C (120 °F).Discard cylinders in a safe place. Do not puncture or burn cylinders.Keep ether cylinders out of the reach of unauthorized personnel.
Illustration 3 g03846587
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 2.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
Proceed to Test Step 4.
2. Check the Wiring Between the ECM and the Ether Control
The ether canister must be removed prior to performing this procedure.
A. Verify that the keyswitch is in the OFF position.
B. Remove the ether canister.
C. Disconnect the engine harness connector for the ether control.
D. Connect a digital voltmeter across the two terminals on the engine harness connector for ether control.
E. Turn the keyswitch to the ON position.
F. Measure the voltage across the terminals while the keyswitch is turned ON.
10 VDC
Result: The voltage measured 0 VDC.
Repair: There is a problem in an electrical component between the ECM and the harness connector for the ether control. The problem may be inside an electrical connector. Make the necessary repairs.
Proceed to Test Step 3.
Result: The voltage measured greater than 10 VDC.
Repair: The electrical components between the ECM and the harness connector for the ether control are OK.
Proceed to Test Step 3.
3. Measure the Resistance of the Coil Inside the Ether Control
A. Verify that the ether control is not connected to the engine harness.
B. Measure the resistance of the coil inside the ether control.
20 Ohms
Result: The measured resistance was approximately 20 Ohms.
Proceed to Test Step 4.
Result: The measured resistance was not approximately 20 Ohms.
Repair: Replace the ether control.
Proceed to Test Step 4.
Illustration 4 g02462341
Retracted plunger
Illustration 5 g02462343
Extended plunger
Table 3
Troubleshooting Test Steps Values Results
4. Perform a "Ether Injection Override"
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Use Cat ET to perform the following override:
- "Ether Injection Override"
C. Verify that the plunger moved up when the override was active.
Plunger Movement
Result: The plunger moved up when the override was active.
Repair: Install the ether bottle. Return to service.
If the proce


Parts see Honda:

96100-62030-00
SEE PART DETAILS - PRI;  BEARING, RADIAL BALL (6203) (Honda Code 0722199).
96100-62030-00 SEE PART DETAILS - PRI; BEARING, RADIAL BALL (6203) (Honda Code 0722199).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB, BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY
31652-881-014
SEE PART DETAILS - SUP; PLUG, RECEPTACLE (Honda Code 1308576).
31652-881-014 SEE PART DETAILS - SUP; PLUG, RECEPTACLE (Honda Code 1308576).
BF15A1 LA, BF15A1 SA, BF15A2 LA, BF15A2 SA, BF15AM LA, BF15AM SA, BF15AW LA, BF15AW SA, BF15AX LA, BF15AX SA, BF15AY LA, BF15AY SA, BF25A1 LHA, BF25A1 SHA, BF25A2 LHA, BF25A2 SHA, BF25A3 LHA, BF25A3 SHA, BF25AW LHA, BF25AW SHA, BF25AX LHA, BF25AX SHA
17661-921-000
SEE PART DETAILS - SUP; PRIMER BULB (Honda Code 0444083).
17661-921-000 SEE PART DETAILS - SUP; PRIMER BULB (Honda Code 0444083).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115AX LA, BF115AX LCA, BF115AX XA, BF115AX XCA,
90604-881-000
 
90604-881-000 SEE PART DETAILS - SUP; CLIP, TUBE (B12) (Honda Code 0498048).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90126-881-000
SEE PART DETAILS - SUP; BOLT, FLANGE (8X45) (Honda Code 0497990).
90126-881-000 SEE PART DETAILS - SUP; BOLT, FLANGE (8X45) (Honda Code 0497990).
BF15A1 LAS, BF15A1 SAS, BF15A1 XAS, BF15A2 LAS, BF15A2 SAS, BF15A2 XAS, BF15AM LAS, BF15AM SAS, BF15AM XAS, BF15AW LAS, BF15AW SAS, BF15AW XAS, BF15AX LAS, BF15AX SAS, BF15AX XAS, BF15AY LAS, BF15AY SAS, BF15AY XAS, BF25AW LHA, BF25AW LHSA, BF25AW LR
58141-881-010
SEE PART DETAILS - PRI; CAP, PROPELLER (Honda Code 0768309).
58141-881-010 SEE PART DETAILS - PRI; CAP, PROPELLER (Honda Code 0768309).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
17620-ZV4-A21
SEE PART DETAILS - SUP; CAP, FUEL FILLER (Honda Code 7446040).
17620-ZV4-A21 SEE PART DETAILS - SUP; CAP, FUEL FILLER (Honda Code 7446040).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AX LA, BF15AX LAS, BF15AX SA, BF15AX SAS, BF15AX XAS, BF15AY LA, BF15AY LAS, BF15AY SA, BF15AY SAS, BF15AY XAS, BF15D3 LGA, BF15D3
Back to top