41100-ZW1-B32ZA SEE PART DETAILS - SUP; CASE ASSY., GEAR (25") (Honda Code 6363691). *NH282MU* (UL-TYPE) (OYSTER SI Honda
BF75AX XRTA, BF75AY XRTA, BF90AX XRTA, BF90AY XRTA
SEE
Price: query
Rating:
Compatible models:
Honda entire parts catalog list:
- GEAR CASE ASSY » 41100-ZW1-B32ZA
- GEAR CASE ASSY. » 41100-ZW1-B32ZA
- GEAR CASE ASSY » 41100-ZW1-B32ZA
- GEAR CASE ASSY. » 41100-ZW1-B32ZA
- GEAR CASE ASSY. » 41100-ZW1-B32ZA
- GEAR CASE ASSY » 41100-ZW1-B32ZA
- GEAR CASE ASSY. » 41100-ZW1-B32ZA
- GEAR CASE ASSY » 41100-ZW1-B32ZA
Information:
Intended Use
This Generator Set is intended for use in generating electrical power.Engine Specifications
Note: The front end of the engine is opposite the flywheel end of the engine. The left and the right sides of the engine are determined from the flywheel end. The number 1 cylinder is the front cylinder.
Illustration 1 g01127295
Cylinder and valve location
(A) Exhaust valves
(B) Inlet valves
Table 1
Specifications for Cat C7.1 Engines for DE150E0 Generator Sets
Operating Range (rpm) 900 to 2800(1)
Number of Cylinders 6 In-Line
Bore 105 mm (4.13 inch)
Stroke 135 mm (5.3 inch)
Aspiration Turbocharged
Compression Ratio 16:1
Displacement 7.01 L (428 inch3)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) The operating rpm is dependent on the engine rating, the application, and the configuration of the throttle.
Table 2
Specifications for Cat C7.1 Engines for DE165E0 and DE200E0 Generator Sets
Operating Range (rpm) 900 to 2800(1)
Number of Cylinders 6 In-Line
Bore 105 mm (4.13 inch)
Stroke 135 mm (5.3 inch)
Aspiration Turbocharged aftercooled
Compression Ratio 16:1
Displacement 7.01 L (428 inch3)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) The operating rpm is dependent on the engine rating, the application, and the configuration of the throttle.Electronic Engine Features
The engine operating conditions are monitored. The Electronic Control Module (ECM) controls the response of the engine to these conditions and to the demands of the operator. These conditions and operator demands determine the precise control of fuel injection by the ECM. The electronic engine control system provides the following features:
Engine monitoring
Engine speed governing
Control of the injection pressure
Cold start strategy
Automatic air/fuel ratio control
Torque rise shaping
Injection timing control
System diagnosticsFor more information on electronic engine features, refer to the Operation and Maintenance Manual, "Features and Controls" topic (Operation Section).Engine Diagnostics
The engine has built-in diagnostics to ensure that the engine systems are functioning correctly. The operator will be alerted to the condition by a "Stop or Warning" lamp. Under certain conditions, the engine horsepower and the vehicle speed may be limited. The electronic service tool may be used to display the diagnostic codes.There are three types of diagnostic codes: active, logged, and event.Most of the diagnostic codes are logged and stored in the ECM. For additional information, refer to the Troubleshooting Manual, "Diagnostic Code Cross Reference" topic.The ECM provides an electronic governor that controls the injector output to maintain the desired engine rpm.Engine Cooling and Lubrication
The cooling system consists of the following components:
Gear-driven centrifugal water pump
Water temperature regulator which regulates the engine coolant temperature
Gear-driven rotor type oil pump
Oil coolerThe engine lubricating oil is supplied by a rotor type oil pump. The engine lubricating oil is cooled and the engine lubricating oil is filtered. The bypass valve can provide unrestricted flow of lubrication oil to the engine if the oil filter element should become plugged.Engine efficiency, efficiency of emission controls, and engine performance depend on adherence to proper operation and maintenance recommendations. Engine performance and efficiency also depend on the use of recommended fuels, lubrication oils, and coolants. Refer to this Operation and Maintenance Manual, "Maintenance Interval Schedule" for more information on maintenance items.Generator
The Series LC generator has the following characteristics:
Single phase or three-phase alternating current
Single bearing
Brushless type
Random wound
Four-pole design
12 wire generator stator
Main stator is 2/3 pitch
Class H insulation
Interference suppression conforming to standard EN 55011, group 1, class BExpected Life
The expected life, defined as total generator set hours, of this generator set is dependent upon many factors including the generator set owner’s desire to rebuild the generator set back to factory specifications. The expected life interval of this generator set is 10,000 service hours. The expected life interval corresponds to the service hours to engine overhaul. At the expected life interval, remove the generator set from operation and consult your Cat dealer for inspect, repair, rebuild, install remanufactured, install new components, or disposal options and to establish a new expected life interval. If a decision is made to remove this generator set from service, refer to Operation and Maintenance Manual, "Decommissioning and Disposal".The following items are required to obtain an economical expected life of this generator set:
Perform regular preventive maintenance procedures as described in the Operation and Maintenance Manual.
Perform generator set inspections as described in the Operation and Maintenance Manual and correct any problems discovered.
Perform system testing as described in the Operation and Maintenance Manual and correct any problems discovered.
Ensure that generator set application conditions comply with Caterpillar’s recommendations.
Ensure that the operating weight does not exceed limits set by manufacturer.
This Generator Set is intended for use in generating electrical power.Engine Specifications
Note: The front end of the engine is opposite the flywheel end of the engine. The left and the right sides of the engine are determined from the flywheel end. The number 1 cylinder is the front cylinder.
Illustration 1 g01127295
Cylinder and valve location
(A) Exhaust valves
(B) Inlet valves
Table 1
Specifications for Cat C7.1 Engines for DE150E0 Generator Sets
Operating Range (rpm) 900 to 2800(1)
Number of Cylinders 6 In-Line
Bore 105 mm (4.13 inch)
Stroke 135 mm (5.3 inch)
Aspiration Turbocharged
Compression Ratio 16:1
Displacement 7.01 L (428 inch3)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) The operating rpm is dependent on the engine rating, the application, and the configuration of the throttle.
Table 2
Specifications for Cat C7.1 Engines for DE165E0 and DE200E0 Generator Sets
Operating Range (rpm) 900 to 2800(1)
Number of Cylinders 6 In-Line
Bore 105 mm (4.13 inch)
Stroke 135 mm (5.3 inch)
Aspiration Turbocharged aftercooled
Compression Ratio 16:1
Displacement 7.01 L (428 inch3)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) The operating rpm is dependent on the engine rating, the application, and the configuration of the throttle.Electronic Engine Features
The engine operating conditions are monitored. The Electronic Control Module (ECM) controls the response of the engine to these conditions and to the demands of the operator. These conditions and operator demands determine the precise control of fuel injection by the ECM. The electronic engine control system provides the following features:
Engine monitoring
Engine speed governing
Control of the injection pressure
Cold start strategy
Automatic air/fuel ratio control
Torque rise shaping
Injection timing control
System diagnosticsFor more information on electronic engine features, refer to the Operation and Maintenance Manual, "Features and Controls" topic (Operation Section).Engine Diagnostics
The engine has built-in diagnostics to ensure that the engine systems are functioning correctly. The operator will be alerted to the condition by a "Stop or Warning" lamp. Under certain conditions, the engine horsepower and the vehicle speed may be limited. The electronic service tool may be used to display the diagnostic codes.There are three types of diagnostic codes: active, logged, and event.Most of the diagnostic codes are logged and stored in the ECM. For additional information, refer to the Troubleshooting Manual, "Diagnostic Code Cross Reference" topic.The ECM provides an electronic governor that controls the injector output to maintain the desired engine rpm.Engine Cooling and Lubrication
The cooling system consists of the following components:
Gear-driven centrifugal water pump
Water temperature regulator which regulates the engine coolant temperature
Gear-driven rotor type oil pump
Oil coolerThe engine lubricating oil is supplied by a rotor type oil pump. The engine lubricating oil is cooled and the engine lubricating oil is filtered. The bypass valve can provide unrestricted flow of lubrication oil to the engine if the oil filter element should become plugged.Engine efficiency, efficiency of emission controls, and engine performance depend on adherence to proper operation and maintenance recommendations. Engine performance and efficiency also depend on the use of recommended fuels, lubrication oils, and coolants. Refer to this Operation and Maintenance Manual, "Maintenance Interval Schedule" for more information on maintenance items.Generator
The Series LC generator has the following characteristics:
Single phase or three-phase alternating current
Single bearing
Brushless type
Random wound
Four-pole design
12 wire generator stator
Main stator is 2/3 pitch
Class H insulation
Interference suppression conforming to standard EN 55011, group 1, class BExpected Life
The expected life, defined as total generator set hours, of this generator set is dependent upon many factors including the generator set owner’s desire to rebuild the generator set back to factory specifications. The expected life interval of this generator set is 10,000 service hours. The expected life interval corresponds to the service hours to engine overhaul. At the expected life interval, remove the generator set from operation and consult your Cat dealer for inspect, repair, rebuild, install remanufactured, install new components, or disposal options and to establish a new expected life interval. If a decision is made to remove this generator set from service, refer to Operation and Maintenance Manual, "Decommissioning and Disposal".The following items are required to obtain an economical expected life of this generator set:
Perform regular preventive maintenance procedures as described in the Operation and Maintenance Manual.
Perform generator set inspections as described in the Operation and Maintenance Manual and correct any problems discovered.
Perform system testing as described in the Operation and Maintenance Manual and correct any problems discovered.
Ensure that generator set application conditions comply with Caterpillar’s recommendations.
Ensure that the operating weight does not exceed limits set by manufacturer.
Parts see Honda:
94301-08140
94301-08140 SEE PART DETAILS - PRI; PIN A, DOWEL (8X14) (Honda Code 0069310).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24221-ZV4-010
24221-ZV4-010 SEE PART DETAILS - PRI; SPRING, CLICK ASSIST (Honda Code 7489727).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90017-P01-003
90017-P01-003 SEE PART DETAILS - SUP; BOLT-WASHER (14X29) (Honda Code 3897949).
BF75AT LHTA, BF75AT LRTA, BF75AT XRTA, BF75AW LHTA, BF75AW LRTA, BF75AW XRTA, BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA, BF90AT LHTA, BF90AT LRTA, BF90AT XRTA, BF90AW JHTA, BF90AW JRTA, BF90AW LHTA, BF90AW LRTA, BF9
04133-P01-305
04133-P01-305 SEE PART DETAILS - PRI; BOLT-WASHER (14X29) (Honda Code 7057300).
BF75AT LHTA, BF75AT LRTA, BF75AT XRTA, BF75AW LHTA, BF75AW LRTA, BF75AW XRTA, BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA, BF90AT LHTA, BF90AT LRTA, BF90AT XRTA, BF90AW JHTA, BF90AW JRTA, BF90AW LHTA, BF90AW LRTA, BF9
99103-MA1-0380
99103-MA1-0380 SEE PART DETAILS - SUP; JET, SLOW (#38) (Honda Code 1981760).
BF75AT LHTA, BF75AT LRTA, BF75AT XRTA, BF75AW LHTA, BF75AW LRTA, BF75AW XRTA, BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA
15400-P0H-305PE
15400-P0H-305PE SEE PART DETAILS - SUP; FILTER, OIL (Honda Code 6424329). (SOLD INDIVIDUALLY)
BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF130A3 LA, BF130A3 LCA,
11821-ZW1-010
11821-ZW1-010 SEE PART DETAILS - PRI; COVER, TIMING BELT (UPPER) (Honda Code 7762594).
BF75A1 LHTA, BF75A1 LRTA, BF75A1 XRTA, BF75A2 LHTA, BF75A2 LRTA, BF75A2 XRTA, BF75A3 LHTA, BF75A3 LRTA, BF75A3 XRTA, BF75A4 LHTA, BF75A4 LRTA, BF75A4 XRTA, BF75A5 LHTA, BF75A5 LRTA, BF75A5 XRTA, BF75A6 LHTA, BF75A6 LRTA, BF75A6 XRTA, BF75AT LHTA, BF7
58130-ZW1-W23
58130-ZW1-W23 SEE PART DETAILS - PRI; PROPELLER, THREE-BLADE (Honda Code 7786783). (13-1/2X15) (AL)
BF115A2 LA, BF115A2 XA, BF115A3 LA, BF115A3 XA, BF115A4 LA, BF115A4 XA, BF115A5 LA, BF115A5 XA, BF115A6 LA, BF115A6 XA, BF115AK0 LA, BF115AK0 XA, BF130A2 LA, BF130A2 XA, BF130A3 LA, BF130A3 XA, BF130A4 LA, BF130A4 XA, BF75A1 LHTA, BF75A1 LRTA, BF75A1