50517-ZV7-020 Honda SEE PART DETAILS - PRI; LEVER, TILT

Table 1
J1939 Code and Description CDL Code and Description Comments
5578-14
Engine Fuel Delivery Absolute Pressure : Special Instruction E489 (1)
Intake Valve Actuation Pressure System Failure The prelubrication cycle completed, but the fuel pressure after the secondary filter is lower than expected.
5580-17
Engine Filtered Fuel Delivery Absolute Pressure : Low - least severe (1) E198 (1)
Low Fuel Pressure The fuel pressure after the secondary fuel filter is lower than expected while the engine is running.
5580-18
Engine Filtered Fuel Delivery Absolute Pressure : Low - moderate severity (2) E198 (2)
Low Fuel Pressure The fuel pressure after the secondary fuel filter is lower than expected while the engine is running.
Table 2
Associated Codes
J1939 Code CDL Code Troubleshooting Procedure
95-0 E390 (3) Troubleshooting, "Fuel Filter Is Restricted"
95-15 E390 (1) Troubleshooting, "Fuel Filter Is Restricted"
95-16 E390 (2) Troubleshooting, "Fuel Filter Is Restricted"
1381-17 E2172 (1) Troubleshooting, "Fuel Transfer Pump Inlet Pressure Is Low"
1382-15 E1129 (1) Troubleshooting, "Fuel Filter Is Restricted"
1382-16 E1129 (2) Troubleshooting, "Fuel Filter Is Restricted"
5417-15 E1569 (1) Troubleshooting, "Clean Fuel Module - Test"
5417-16 E1569 (2) Troubleshooting, "Clean Fuel Module - Test"
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Turn the keyswitch to ON.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Fuel Tank Level
A. Turn the keyswitch to OFF.
B. Inspect the fuel level to make sure that the tank level is not too low.
Fuel Level
Result: The fuel level is OK.
Proceed to Test Step 3.
Result: The fuel level is NOT OK.
Repair: Add fuel to the fuel tank.
Proceed to Test Step 13.
3. Check for Fuel Leaks
A. Turn the keyswitch to OFF.
B. Inspect the low-pressure fuel system for leaks.
C. Check the low-pressure fuel system connections to make sure that the connectors are properly torqued.
D. Check the fuel filter drain plug fittings.
E. Check for air in the fuel. Refer to Testing and Adjusting, "Air in Fuel - Test" for the proper procedure.
Fuel Tank
Result: A fuel leak was found.
Repair: Repair the cause of the fuel leak. Replace parts as necessary.
Proceed to Test Step 13.
Result: There are no fuel leaks.
Proceed to Test Step 4.
4. Prime the Fuel System
A. Use the manual priming switch to prime the fuel system.
Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
Fuel System Primed
Result: The fuel system priming sequence was completed.
Proceed to Test Step 5.
5. Check the Fuel Pressure Sensor
A. Turn the keyswitch to ON.
B. Connect to Cat ET.
C. Monitor the following parameter in the status screen:
- "Fuel Pressure"
Fuel Pressure
Result: The fuel pressure reading is 0 11 kPa (0 2 psi).
Repair: For an E198 or 5580 code, proceed to Test Step 6.
For a 5578 code, proceed to Test Step 9.
Result: The fuel pressure reading is NOT 0 11 kPa (0 2 psi).
Repair: Replace the fuel pressure sensor.
Proceed to Test Step 13.
Illustration 1 g06101717
(1) Starting priority valve
(2) Low-pressure fuel system pressure regulator
Table 4
Troubleshooting Test Steps Values Results
6. Check the Low-Pressure Fuel System Pressure Regulator
A. Turn the keyswitch to OFF.
B. Remove the low-pressure fuel system pressure regulator from the secondary fuel filter auxiliary manifold. Refer to the Disassembly and Assembly manual for proper procedure.
C. Check the low-pressure fuel system pressure regulator by actuating the spool within the cartridge assembly.
Low-Pressure Fuel System Pressure Regulator
Result: The low-pressure fuel system pressure regulator is OK.
Repair: Reinstall the low-pressure fuel system pressure regulator.
Proceed to Test Step 7.
Result: The low-pressure fuel system pressure regulator is NOT OK.
Repair: Replace the low-pressure fuel system pressure regulator.
Proceed to Test Step 13.
Illustration 2 g06101760
(3) Low-pressure fuel system pressure relief valve
Table 5
Troubleshooting Test Steps Values Results
7. Check the Fuel Transfer Pump Pressure Relief Valve
A. Turn the keyswitch to OFF.
B. Remove the fuel transfer pump pressure rel