16730-ZY6-013 Honda SEPARATOR ASSY., VAPOR (Honda Code 8445066).


16730-ZY6-013 SEPARATOR ASSY., VAPOR (Honda Code 8445066). Honda BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF150A6 LA, BF150A6 XA, BF150A6 XCA, BF150AK0 LA, BF150AK0 XA, BF150AK0 XCA SEPARATOR
16730-ZY6-013 SEPARATOR ASSY., VAPOR (Honda Code 8445066). Honda
Rating:
23

Buy SEPARATOR ASSY., VAPOR (Honda Code 8445066). 16730-ZY6-013 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 32
 

Honda entire parts catalog list:

BF135A6 LA 2006
BF135A6 XA 2006
BF135A6 XCA 2006
BF135AK0 LA 2007
BF135AK0 XA 2007
BF135AK0 XCA 2007
BF150A6 LA 2006
BF150A6 XA 2006
BF150A6 XCA 2006
BF150AK0 LA 2007
BF150AK0 XA 2007
BF150AK0 XCA 2007

Information:

Start By:a. remove crankshaft pulley and vibration damper
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Remove four bolts (1) from adapter (2), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (4) and crankshaft seal (3) from adapter (2).
Typical Example3. Install tool (B) in the adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (5). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal & Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak.
1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3).3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean 1P0808 All Purpose Lubricant on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft pulley and vibration damper


Parts separator Honda:

16730-ZY6-023
SEPARATOR ASSY., VAPOR
16730-ZY6-023 SEPARATOR ASSY., VAPOR
BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF150A4 LA, BF150A4 XA, BF150A4 XCA, BF150A5 LA, BF150A5 XA, BF150A5 XCA, BF150A6 LA, BF150A6 XA, B
16800-ZY6-003
SEPARATOR ASSY., WATER (Honda Code 7633845).
16800-ZY6-003 SEPARATOR ASSY., WATER (Honda Code 7633845).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
16730-ZY6-043
 
16730-ZY6-043 SEPARATOR ASSY., VAPOR (NOT AVAILABLE)
BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF150AK0 LA, BF150AK0 XA, BF150AK0 XCA
Back to top