40202-ZY9-610ZC SEPARATOR, EXTENSION *NHB14M* (XL) (AQUA MARINE SILVER METARIC) Honda
BF60AK1 XRTA, BF90DK2 XRTA, BFP60AK1 XRTA
SEPARATOR
Price: query
Rating:
Compatible models:
Honda entire parts catalog list:
- EXTENSION CASE » 40202-ZY9-610ZC
- GEAR CASE » 40202-ZY9-610ZC
- EXTENSION CASE » 40202-ZY9-610ZC
Information:
START BY:a. remove fuel injection pumpsb. disassemble governorc. remove fuel transfer pump 1. Loosen screws (1) in the levers, and remove screws (3) in the crossover lever. Slide shaft assembly (2) out of the housing. 2. Loosen the screws in levers (4), and remove the screw in crossover lever (5). Slide shaft (6) out of the housing. Put identification marks on lifters (7) and rollers (8) for installation in their respective bores in the housing.3. Use a magnet to remove eight lifter assemblies (7). 4. Remove roller (8) from each lifter assembly. 5. Turn the camshaft so the groove (slot) for the timing pin is in the position shown, and carefully remove camshaft (9). Remove the thrust washer from the housing. 6. Remove camshaft rear bearing (10) from the fuel injection pump housing. Be careful not to damage the bearing bore in the housing. 7. Use tool group (A) to remove the camshaft front bearing from the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Put clean fuel on all parts during assembly.1. Use tooling (A) to install the camshaft front bearing in the housing. Install the bearing with the chamfer toward the inside of the pump housing.2. Install the bearing so it is even with the front face of the pump housing. 3. Use tooling (B) to machine the bore in the camshaft front bearing to the correct size. See Special Instruction, Form No. SMH6735 for the procedure to machine the new camshaft front bearing. The bore in the bearing must be 25.413 0.013 mm (1.0005 .0005 in.). 4. Use tooling (A) to install the camshaft rear bearing in the housing. Install the bearing so groove (1) in the bearing is in the position shown. On earlier pump housings without a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.114 0.025 mm (.0045 .0010 in.) below face (X) on the housing. On later pump housings with a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.43 0.13 mm (.017 .005 in.) below the counterbore for the thrust washer. 5. Install thrust washer (2) in the housing with the ear on the thrust washer in the hole in the pump housing so the thrust washer will not turn.
If the pump housing is assembled while it is in a horizontal position, the thrust washer can slide out of the counterbore and into the area between the camshaft thrust face and the housing. Then the fuel pump camshaft end play will not be correct, and it will be necessary to disassemble the fuel pump housing so the thrust washer can be installed correctly.
6. With the pump housing in a vertical position as shown, carefully install camshaft (3). To make sure that the thrust washer will be kept in its correct installation location, keep the pump housing in a vertical position, and install the fuel transfer pump and camshaft sleeve. See Fuel Transfer Pump Installation for the procedure to install the fuel transfer pump and camshaft sleeve. 7. Install each roller (4) in their respective lifters. 8. Use a magnet to install lifter assemblies (5) in their respective bores in the pump housing. Install the lifter assemblies with the groove in each lifter in alignment with the dowel in the lifter bore. 9. Install shaft (6) in the pump housing. Install the shaft through one lever (7), through crossover lever (8) and through three levers (7) as shown. Install the screw in crossover lever (8). Tighten the screw in crossover lever (8). Tighten the screw to a torque of 2.70 0.25 mm (24 2 lb.in.). Do not tighten any of the screws in the levers. 10. Install shaft assembly (9) in the pump housing; then through three levers (11) as shown. Install the screw in crossover lever (10). Tighten the screw to a torque of 2.8 0.2 mm (24 2 lb.in.). Do not tighten any of the screws in the levers.11. After connecting the governor to the fuel injection pump housing, installing the fuel injection pumps and installing the fuel transfer pump, adjust the following:a. Adjust the crossover levers.b. Adjust fuel pump calibration.c. Adjust the fuel setting.d. Adjust high and low idle speeds.See Testing And Adjusting for the above procedures.END BY:a. connection of governor to fuel injection pump housingb. install fuel injection pumpsc. install fuel transfer pump
Put clean fuel on all parts during assembly.1. Use tooling (A) to install the camshaft front bearing in the housing. Install the bearing with the chamfer toward the inside of the pump housing.2. Install the bearing so it is even with the front face of the pump housing. 3. Use tooling (B) to machine the bore in the camshaft front bearing to the correct size. See Special Instruction, Form No. SMH6735 for the procedure to machine the new camshaft front bearing. The bore in the bearing must be 25.413 0.013 mm (1.0005 .0005 in.). 4. Use tooling (A) to install the camshaft rear bearing in the housing. Install the bearing so groove (1) in the bearing is in the position shown. On earlier pump housings without a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.114 0.025 mm (.0045 .0010 in.) below face (X) on the housing. On later pump housings with a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.43 0.13 mm (.017 .005 in.) below the counterbore for the thrust washer. 5. Install thrust washer (2) in the housing with the ear on the thrust washer in the hole in the pump housing so the thrust washer will not turn.
If the pump housing is assembled while it is in a horizontal position, the thrust washer can slide out of the counterbore and into the area between the camshaft thrust face and the housing. Then the fuel pump camshaft end play will not be correct, and it will be necessary to disassemble the fuel pump housing so the thrust washer can be installed correctly.
6. With the pump housing in a vertical position as shown, carefully install camshaft (3). To make sure that the thrust washer will be kept in its correct installation location, keep the pump housing in a vertical position, and install the fuel transfer pump and camshaft sleeve. See Fuel Transfer Pump Installation for the procedure to install the fuel transfer pump and camshaft sleeve. 7. Install each roller (4) in their respective lifters. 8. Use a magnet to install lifter assemblies (5) in their respective bores in the pump housing. Install the lifter assemblies with the groove in each lifter in alignment with the dowel in the lifter bore. 9. Install shaft (6) in the pump housing. Install the shaft through one lever (7), through crossover lever (8) and through three levers (7) as shown. Install the screw in crossover lever (8). Tighten the screw in crossover lever (8). Tighten the screw to a torque of 2.70 0.25 mm (24 2 lb.in.). Do not tighten any of the screws in the levers. 10. Install shaft assembly (9) in the pump housing; then through three levers (11) as shown. Install the screw in crossover lever (10). Tighten the screw to a torque of 2.8 0.2 mm (24 2 lb.in.). Do not tighten any of the screws in the levers.11. After connecting the governor to the fuel injection pump housing, installing the fuel injection pumps and installing the fuel transfer pump, adjust the following:a. Adjust the crossover levers.b. Adjust fuel pump calibration.c. Adjust the fuel setting.d. Adjust high and low idle speeds.See Testing And Adjusting for the above procedures.END BY:a. connection of governor to fuel injection pump housingb. install fuel injection pumpsc. install fuel transfer pump
Parts separator Honda:
16730-ZZ3-003
16730-ZZ3-003 SEPARATOR ASSY., VAPOR
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
16800-ZY9-003
16800-ZY9-003 SEPARATOR ASSY., WATER (Honda Code 8575904).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA