41160-ZW6-000 Honda SHAFT, PROPELLER (Honda Code 6007397).


41160-ZW6-000 SHAFT, PROPELLER (Honda Code 6007397). Honda BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB, BF2D3 SCAB, BF2D3 SCHA, BF2D3 SHA, BF2D4 LCHA, BF2D SHAFT
41160-ZW6-000 SHAFT, PROPELLER (Honda Code 6007397). Honda
Rating:
8

Buy SHAFT, PROPELLER (Honda Code 6007397). 41160-ZW6-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Honda entire parts catalog list:

BF2.3DK2 LCHA 2007
BF2.3DK2 SCHA 2007
BF2D1 LCHA 2001
BF2D1 SA 2001
BF2D1 SAB 2001
BF2D1 SCAB 2001
BF2D1 SCHA 2001
BF2D1 SHA 2001
BF2D2 LCHA 2002
BF2D2 SA 2002
BF2D2 SAB 2002
BF2D2 SCAB 2002
BF2D2 SCHA 2002
BF2D2 SHA 2002
BF2D3 LCHA 2003
BF2D3 SA 2003
BF2D3 SAB 2003
BF2D3 SCAB 2003
BF2D3 SCHA 2003
BF2D3 SHA 2003
BF2D4 LCHA 2004
BF2D4 SA 2004
BF2D4 SAB 2004
BF2D4 SCAB 2004
BF2D4 SCHA 2004
BF2D4 SHA 2004
BF2D5 LCHA 2005
BF2D5 SCAB 2005
BF2D5 SCHA 2005
BF2D5 SHA 2005
BF2D6 LCHA 2006
BF2D6 SCAB 2006
BF2D6 SCHA 2006
BF2D6 SHA 2006
BF2DK0 LCHA 2007
BF2DK0 SCAB 2007
BF2DK0 SCHA 2007
BF2DX LCHA 1999
BF2DX SA 1999
BF2DX SAB 1999
BF2DX SCAB 1999
BF2DX SCHA 1999
BF2DY LCHA 2000
BF2DY SA 2000
BF2DY SAB 2000
BF2DY SCAB 2000
BF2DY SCHA 2000
BF2DY SHA 2000

Information:

If the air cleaner element becomes plugged, the air can split the material of the air cleaner element. Unfiltered air will drastically accelerate internal engine wear. Your Cat dealer has the proper air cleaner elements for your application. Consult your Cat dealer for the correct air cleaner element.
Check the precleaner (if equipped) daily for accumulation of dirt and debris. Remove any dirt and debris, as needed.
Operating conditions (dust, dirt, and debris) may require more frequent service of the air cleaner element.
The air cleaner element should be replaced every 2 years. This replacement should be performed regardless of the number of cleanings.Note: This air cleaner element should be replaced after the third cleaning.Note: Use the 102-9720 Cleaning Kit. This product contains the detergent and oil that is made specifically for the maintenance of the air cleaner elements.Cleaning the Air Filter Element
Illustration 1 g03705911
Loosen and remove the air cleaner element clamp (1).
Remove the air cleaner element (2). Tap the air cleaner element to dislodge dirt particles. Gently brush the air cleaner element with a soft bristle brush.
Do not use gasoline, steam, caustic or unapproved detergents, or parts cleaning solvents. Do not use high pressure water or air to clean the air cleaner element. Any of those liquids or methods can cause air cleaner element damage.
Spray the air cleaner element with the cleaning solution. Allow the air cleaner element to stand for 10 minutes.
Rinse the air cleaner element with low water pressure. The maximum water pressure for this procedure is 275 kPa (40 psi). Tap water is acceptable. Start to rinse the air cleaner element from the clean side (inside). Next, clean the dirty side (outside) in order to flush out dirt. Inspect the air cleaner element for tears and/or holes after the air cleaner element is cleaned. Do not reuse damaged air cleaner elements.
Do not use compressed air, open flame, or hot air to dry the air cleaner element. Excess heat shrinks cotton fiber, and compressed air may blow holes in the material. Allow the air cleaner element to air dry.
Shake excess water off the air cleaner element , and allow the air cleaner element to air dry. Drying the air cleaner element in the sun speeds the process.
Do not use transmission fluid, engine oil, diesel fuel, or other lubricant to oil the air cleaner element. The air cleaner element can not function correctly if improper oil is used. Never operate an engine with a dry air cleaner element. The air cleaner element can not function correctly without oil. Always saturate the clean air cleaner element with the recommended oil.
The dry air cleaner element should be oiled before installation. Apply small amounts of oil across the top of each pleat. Allow the oil to soak into the air cleaner element for 20 minutes. Oil any remaining "white" spots.
Inspect the housing and the clamp for air cleaner element (1). Install the clean, oiled air cleaner element. Replace the clamp, if necessary. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque of the clamp. Replacing the Air Filter
Loosen and remove the air cleaner clamp (1).
Remove air cleaner.
Install clamp (1).
Install a new air cleaner element (2).
Tighten the air cleaner clamp (1).


Parts shaft Honda:

22257-ZW6-000
 
22257-ZW6-000 SHAFT, EXTENSION
BF2D1 SA, BF2D1 SAB, BF2D1 SHA, BF2D2 SA, BF2D2 SAB, BF2D2 SHA, BF2D3 SA, BF2D3 SAB, BF2D3 SHA, BF2D4 SA, BF2D4 SAB, BF2D4 SHA, BF2D5 SHA, BF2D6 SHA, BF2DX SA, BF2DX SAB, BF2DY SA, BF2DY SAB, BF2DY SHA
Back to top