24113-ZW1-B00 Honda SLIDER, SHIFT (Honda Code 6015556).


24113-ZW1-B00 SLIDER, SHIFT (Honda Code 6015556). Honda BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA, BF90AX LHTA, BF90AX LRTA, BF90AX XRTA, BF90AY LHTA, BF90AY LRTA, BF90AY XRTA SLIDER
24113-ZW1-B00 SLIDER, SHIFT (Honda Code 6015556). Honda
Rating:
73

Buy SLIDER, SHIFT (Honda Code 6015556). 24113-ZW1-B00 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Honda entire parts catalog list:

BF75AX LHTA 1999
BF75AX LRTA 1999
BF75AX XRTA 1999
BF75AY LHTA 2000
BF75AY LRTA 2000
BF75AY XRTA 2000
BF90AX LHTA 1999
BF90AX LRTA 1999
BF90AX XRTA 1999
BF90AY LHTA 2000
BF90AY LRTA 2000
BF90AY XRTA 2000

Information:


Table 1
Parameter Value
Engine Oil Pressure at rated rpm 280 to 600 kPa (40 to 87 psi)
Minimum Engine Oil Pressure at low idle 140 kPa (20 psi) Required Tools
Table 2
Required Tools
Part Number Qty
1U-5470 Engine Pressure Gp 1
Illustration 1 g00296486
1U-5470 Engine Pressure Group
The 1U-5470 Engine Pressure Group measures the engine oil pressure in the system. This engine tool group can read the engine oil pressure inside the oil manifold.Note: Refer to Special Instruction, SEHS8907, "Using the 1U-5470 Engine Pressure Group" for more information on using the 1U-5470 Engine Pressure Group.Note: The engine oil pressure can also be measured by using an electronic service tool. Refer to Troubleshooting for information on the use of the Caterpillar Electronic Technician (ET).Test Preparation
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Turn off the engine.
Illustration 2 g03710256
Location of the oil gallery plug
Typical example of the right-hand side of the engine
(1) Plug
Remove plug (1).
Install the 1U-5470 Engine Pressure Gp into the open oil gallery port.
Install the 1U-5470 Engine Pressure Group into oil gallery plug (1). Test Procedure
Check the engine oil pressure to the camshaft and main bearings on each side of the cylinder block at oil gallery plug (1).
Start the engine. Run the engine with SAE 10W30 or SAE 15W40 oil. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil. Note: Allow the engine to reach operating temperature before you perform the oil pressure test.Note: The engine oil temperature should not exceed 115 °C (239 °F).
Record the value of the engine oil pressure when the engine has reached operating temperature.
A record of engine oil pressure can be used as an indication of possible engine problems or of damage. A possible problem could exist if the engine oil pressure suddenly increases or decreases 70 kPa (10 psi) and the engine is not at normal engine oil pressure. Inspect the engine and correct the problem.
Compare the recorded engine oil pressure with the engine oil pressure indicators on the instrument panel and the engine oil pressure that is displayed on the Cat ET.
An engine oil pressure indicator or sensor that has a defect can give a false indication of engine oil pressure. If, there is a notable difference between the engine oil pressure readings make necessary repairs.
If the engine oil pressure is low, refer to Testing and Adjusting, "Engine Oil Pressure is Low" for the possible causes of low engine oil pressure.
If the engine oil pressure is high, refer to Testing and Adjusting, "Engine Oil Pressure is High" for the possible causes of high engine oil pressure.


Parts slider Honda:

24113-ZW5-000
 
24113-ZW5-000 SLIDER, SHIFT (Honda Code 5891650).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24122-ZW1-B00
 
24122-ZW1-B00 SLIDER, SHIFT (Honda Code 6015564).
BF75AX LHTA, BF75AX LRTA, BF75AX XRTA, BF75AY LHTA, BF75AY LRTA, BF75AY XRTA, BF90AX LHTA, BF90AX LRTA, BF90AX XRTA, BF90AY LHTA, BF90AY LRTA, BF90AY XRTA
Back to top