24122-ZV1-300 Honda SLIDER, SHIFT (Honda Code 1984616).


24122-ZV1-300 SLIDER, SHIFT (Honda Code 1984616). Honda BF5A1 LA, BF5A1 SA, BF5A2 LA, BF5A2 SA, BF5A3 LA, BF5A3 SA, BF5A4 LA, BF5A4 SA, BF5A5 LA, BF5A5 SA, BF5A6 LA, BF5A6 SA, BF5AK0 LA, BF5AK0 SA, BF5AK2 LA, BF5AK2 SA, BF5AK3 LA, BF5AK3 SA, BF5AM LA, BF5AM SA, BF5AW LA, BF5AW SA, BF5AX LA, BF5AX SA, BF5A SLIDER
24122-ZV1-300 SLIDER, SHIFT (Honda Code 1984616). Honda
Rating:
58

Buy SLIDER, SHIFT (Honda Code 1984616). 24122-ZV1-300 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Honda entire parts catalog list:

BF5A1 LA 2001
BF5A1 SA 2001
BF5A2 LA 2002
BF5A2 SA 2002
BF5A3 LA 2003
BF5A3 SA 2003
BF5A4 LA 2004
BF5A4 SA 2004
BF5A5 LA 2005
BF5A5 SA 2005
BF5A6 LA 2006
BF5A6 SA 2006
BF5AK0 LA 2007
BF5AK0 SA 2007
BF5AK2 LA 2007
BF5AK2 SA 2007
BF5AK3 LA 2007
BF5AK3 SA 2007
BF5AM LA 1997
BF5AM SA 1997
BF5AW LA 1998
BF5AW SA 1998
BF5AX LA 1999
BF5AX SA 1999
BF5AY LA 2000
BF5AY SA 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
6V-8675 Bolt 2
5P-8245 Hard Washer 2
B 350-7768 Electric Hydraulic Pump Gp (115 V) 1
350-7769 Electric Hydraulic Pump Gp (230 V) 1
316-1493 Hydraulic Puller As 1
FT-1410 Sleeve 1
- Puller Stud 1
8T-1757 Nut 1
9X-8268 Washer 1
C - P-80 Rubber Lubricant - Start By:
Remove the bottom guards.
Remove the engine side guards.
Remove the hood.
Remove the bulldozer lift cylinders.
Personal injury can result from hot coolant, steam, and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and allow sufficient time for the cooling system to cool.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining procedure.
Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil – Change" for the correct draining procedure.
Illustration 1 g06452167
Remove the bolts and disconnect hose assembly (1). Disconnect the harness assembly that is located inside hose assembly (1).
Remove the bolts and disconnect hose assembly (2).
Remove the bolts and disconnect hose assembly (3).
Remove bolts (4) and position hose assembly (1), hose assembly (2), and hose assembly (3) out of the way.
Illustration 2 g06469851
Cut cable strap (5).
Remove bolt (7) and the clip. Disconnect hose (6). Position hose (6) out of the way.
Cut cable strap (10), loosen clamp (8), and disconnect hose (9). Position hose (9) out of the way.
Illustration 3 g06469859
Loosen clamp (11) and disconnect hose (12). Position hose (12) out of the way.
Loosen clamp (13) and disconnect hose (14). Position hose (14) out of the way.
Illustration 4 g06470001
Loosen clamp (15) and disconnect hose (19).
Remove bolt (17) and the clip. Position hose (19) out of the way.
Loosen clamp (16) and disconnect hose (18). Position hose (18) out of the way.


Back to top