98069-57756 Honda SPARK PLUG (X22ESR-UB)

Illustration 1 g01191595
Typical schematicTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Thoroughly inspect the J1/P1 or J2/P2 ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 2 g01192209
P1 terminals that are associated with the 5 volt supply (P1-2) +5 VDC (P1-3) Return
Illustration 3 g01149851
P2 terminals that are associated with the 5 volt supply (P2-2) +5 VDC (P2-3) Return (P2-41) +5 VDC (P2-42) Return
Illustration 4 g01123211
Connectors for the sensors (A) Supply (B) Return (C) Signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the 5 volt supply.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points from each sensor back to the ECM.Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore electrical power to the ECM.
Use Cat ET to check for active diagnostic codes. Wait at least 30 seconds so that any codes may become active. Check for these codes:
262-03
262-04Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active.Repair: If any of the above codes are logged and the engine is not running properly, refer to Troubleshooting, "Troubleshooting Without a Diagnostic Code".If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - Either the 262-03 or 262-04 diagnostic code is active at this time. Proceed to Test Step 3.Test Step 3. Disconnect the Pressure Sensors and Check for Active Diagnostic Codes
Restore electrical power to the engine ECM.
Monitor the active diagnostic code screen on Cat ET while you disconnect each pressure sensor connector. Check for an active 262-03 code or an active 262-04 code.Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Disconnect the following sensors one at a time:
Engine oil pressure sensor
Turbocharger outlet pressure sensor
Fuel pressure sensor
Injection actuation pressure sensor
Atmospheric pressure sensor
Turbocharger Inlet pressure sensor
Remove electrical power from the ECM.Expected Result:The diagnostic code deactivates when a particular sensor is disconnected.Results:
OK - The 262-03 or 262-04 diagnostic code deactivates when a particular sensor is disconnected.Repair: Connect the suspect sensor. If the code returns, replace the sensor. Connect all of the connectors. Verify that the problem is resolved.STOP
Not OK - The 262-03 or 262-04 diagnostic code remains active after all of the sensors are disconnected. Leave the sensors disconnected. The sensors are not the cause of the diagnostic code. Proceed to Test Step 4.Test Step 4. Check the Supply Voltages at the ECM
Disconnect the J1/P1 and J2/P2 ECM connectors.
Fabricate six jumper wires that are long enough to be used to measure the supply voltage at the ECM connectors. Crimp connector sockets to one end of each jumper wire.
Remove the wires from terminal locations P1-2 (5 V sensor supply) and P1-3 (sensor return). Install a jumper wire into each of these terminal locations.
Remove the wires from terminal locations P2-2 (5 V sensor supply) and P2-3 (sensor return). Install a jumper wire into each of these terminal locations.
Remove the wires from terminal locations P2-41 (5 V sensor supply) and P2-42 (sensor return). Install a jumper wire into each of these terminal locations.
Connect ECM connectors J1/P1 and J2/P2.
Restore electrical power to the engine ECM.
Measure the voltage between