14511-PNA-003 Honda STOPPER (TOOL)

Troubleshooting
Troubleshooting can be difficult. On the following pages there is a list of possible problems. To make a repair to a problem, make reference to the cause and correction.This list of problems, causes, and corrections, will only give an indication of where a possible problem can be, and what repairs are needed. Normally, more or other repair work is needed beyond the recommendations in the list. Remember that a problem is not normally caused only by one part, but by the relation of one part with other parts. This list can not give all possible problems and corrections. The serviceman must find the problem and its source, then make the necessary repairs.1. Engine Fails to Start2. Misfiring3. Stalls at Low Speed4. Erratic Engine Speed5. Low Power6. Excessive Vibration7. Heavy Combustion Knock8. Valve Train Clicking Noise9. Oil in Coolant10. Mechanical Knock11. Excessive Fuel Consumption12. Loud Valve Train Noise13. Excessive Valve Lash14. Valve Spring Retainer Free15. Slobber16. Valve Lash Close-up17. Premature Engine Wear18. Coolant in Engine Lubricating Oil19. Excessive Black or Gray Smoke20. Excessive White or Blue Smoke21. Low Engine Oil Pressure22. High Lubricating Oil Consumption23. Abnormal Engine Coolant Temperature24. Starting Motor Fails to Crank25. Alternator Fails to Charge26. Alternator Charging Rate Low or Unsteady27. Alternator Charging Rate Excessive28. Noisy Alternator29. High Exhaust TemperatureEngine Fails To Start Misfiring Stalls At Low Speed Erratic Engine Speed Low Power Excessive Vibration Heavy Combustion Knock Valve Train Clicking Noise Oil In Coolant Mechanical Knock Excessive Fuel Consumption Loud Valve Train Noise Excessive Valve Lash Valve Spring Retainer Free Slobber Valve Lash Close-Up Premature Engine Wear Coolant In Engine Lubricating Oil Excessive Black Or Gray Smoke Excessive White Or Blue Smoke Low Engine Oil Pressure High Lubricating Oil Consumption Abnormal Engine Coolant Temperature Starting Motor Fails To Crank Alternator Fails To Charge Alternator Charging Rate Low Or Unsteady Alternator Charging Rate Excessive (As Evidenced By Lights Burning Out, Battery Requires Too Much Water.) Noisy Alternator High Exhaust Temperature Fuel System
Difficulty within the fuel system can be classed in one of two groups: lack of fuel or too much fuel for proper combustion.Many times, the fuel system is blamed when the fault lies elsewhere, expecially when smoky exhaust is the problem. Smoky exhaust can be the result of a faulty fuel injection valve, but it can also be caused by lack of air for complete combustion, overloading at high altitude, excessive oil burning or lack of compression.Troubleshooting The Fuel Supply System
1. Observe the fuel pressure gauge reading. Lack of pressure indicates difficulty in the supply side of the system.2. Check the fuel level in the supply tank and the fuel tank cap vent for being plugged.3. See that the vent valve is closed.4. Check for leakage in the fuel supply lines and components or for a kinked or restricted supply line.5. Replace the fuel filter element and clean the primary fuel filter if so equipped.6. Inspect the fuel bypass valve to see that it moves freely and that dirt is not holding the plunger off its seat. Be certain the spring has correct tension.7. Bleed the fuel system to remove trapped air.8. Test the fuel transfer pump.To test the fuel transfer pump, connect an 8M2743 Pressure Gauge which is part of 7S8875 Hydraulic Test Box in place of the fuel pressure gauge line at the filter housing.The pressure should be:Full load ... 31 5 psi(2.18 0.35 kg/cm2) (214 34 kPa)Low idle ... min. 20 psi(1.41 kg/cm2) (138 kPa)Cranking speed ... 10 to 20 psi(0.7 to 1.41 kg/cm2) (69 to 138 kPa)Testing Fuel Injection Equipment
Always inspect the seats of both the nozzle and the precombustion chamber prior to installing a fuel injection valve. The nozzle assembly should be finger tight on the body. It is important to maintain the nozzle retaining nut torque to 105 5 lb. ft. (142 7 N m). Excessive torque will damage the nozzle. Less torque can cause the nozzle case to bulge or split and will allow the nozzle to leak resulting in fuel dilution of the crankcase oil. Any loose fuel line connections inside the camshaft housings can cause crankcase dilution and result in low oil pressure, bearing wear, and engine damage.Before attempting to test a fuel injection pump or valve in an engine that is missing or puffing black smoke, make a simple check to determine which cylinder is causing the difficulty. While operating the engine at a speed which makes the defect most pronounced, momentarily loosen a fuel line nut at the fuel injection pump sufficiently to "cut out" one cylinder. Check all cylinders in the same manner. If, after cutting out a cylinder, there is no noticeable difference in engine operation, or if this action causes puffing or black smoke to cease, the pump and valve for only that cylinder need be tested.Checking Fuel Injection Valves
Examine fuel injection valves for:1. Excessive carbon on tip of nozzle or in orifice.2. Erosion of the orifice.3. Screen plugged with dirt.The condition of a capsule-type nozzle assembly can be tested on the Caterpillar Diesel Fuel Injection Test Apparatus, and the nozzle leakage rate can be determined.Removing and Installing Fuel Injection Pump Assemblies
1. Remove the timing pin from its storage position and install one of the retaining bolts (head down) through one of the flange holes. Install a nut at the top to hold the bolt in place. The bolt head limits the depth the pin can be inserted into the housing.2. Insert timing pin (1) in the timing hole. Move the governor control or rack linkage back and forth slowly to allow the pin to pass through the notch in the rack. The pin is in place when the head of the inverted bolt touches the fuel pump housing. With the rack in this position, the center line of the second tooth on each fuel pump gear segment, will be aligned with the correct tooth on the rack. With the rack located in this manner, a zero reference point is established.
TIMING PIN ZEROES THE RACK
1. Timing Pin.