56000-ZW9-W51 Honda TILT ASSY., POWER (Honda Code 7550320).


56000-ZW9-W51 TILT ASSY., POWER (Honda Code 7550320). Honda BF9.9D4 SRTA, BF9.9D5 SRTA, BF9.9D6 SRTA, BFP8D4 LHTA, BFP8D4 LRTA, BFP8D5 LHTA, BFP8D5 LRTA, BFP8D6 LHTA, BFP8D6 LRTA, BFP8DK0 LHTA, BFP8DK0 LRTA, BFP8DK2 LHTA, BFP8DK2 LRTA, BFP9.9D4 LHTA, BFP9.9D4 LRTA, BFP9.9D4 XHTA, BFP9.9D4 XRTA, BFP9.9D5 LHTA, TILT
56000-ZW9-W51 TILT ASSY., POWER (Honda Code 7550320). Honda
Rating:
88

Buy TILT ASSY., POWER (Honda Code 7550320). 56000-ZW9-W51 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Honda entire parts catalog list:

BF9.9D4 SRTA 2004
BF9.9D5 SRTA 2005
BF9.9D6 SRTA 2006
BFP8D4 LHTA 2004
BFP8D4 LRTA 2004
BFP8D5 LHTA 2005
BFP8D5 LRTA 2005
BFP8D6 LHTA 2006
BFP8D6 LRTA 2006
BFP8DK0 LHTA 2007
BFP8DK0 LRTA 2007
BFP8DK2 LHTA 2007
BFP8DK2 LRTA 2007
BFP9.9D4 LHTA 2004
BFP9.9D4 LRTA 2004
BFP9.9D4 XHTA 2004
BFP9.9D4 XRTA 2004
BFP9.9D5 LHTA 2005
BFP9.9D5 LRTA 2005
BFP9.9D5 XHTA 2005
BFP9.9D5 XRTA 2005
BFP9.9D6 LHTA 2006
BFP9.9D6 LRTA 2006
BFP9.9D6 XHTA 2006
BFP9.9D6 XRTA 2006
BFP9.9DK0 LHTA 2007
BFP9.9DK0 LRTA 2007
BFP9.9DK0 XHTA 2007
BFP9.9DK0 XRTA 2007

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
5580-0
Engine Filtered Fuel Delivery Absolute Pressure : High - most severe (3) E096 (3)
High Fuel Pressure The fuel pressure is above the trip point pressure.
The code is logged.
5580-15
Engine Filtered Fuel Delivery Absolute Pressure : High - least severe (1) E096 (1)
High Fuel Pressure The fuel pressure is above the trip point pressure.
The code is logged.
5580-16
Engine Filtered Fuel Delivery Absolute Pressure : High - moderate severity (2) E096 (2
High Fuel Pressure The fuel pressure is above the trip point pressure.
The code is logged. Probable Causes
Codes
Sensor
Fuel lines
Transfer pump
Pressure regulatorRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Fuel Pressure Sensor
A. Connect Cat ET.
B. Use Cat ET to monitor the following pressure:
- Fuel pressure
C. Use a mechanical gauge to check the system fuel pressure. Refer to Systems Operation/Testing and Adjusting, "Fuel Pressure" for additional information.
Note: If a mechanical gauge is not available, determine if the fuel pressure reading on Cat ET is reasonable.
Sensor
Result: The gauge value of the fuel pressure is reasonable when compared to the fuel pressure reading shown in Cat ET.
Proceed to Test Step 3.
Result: The gauge value of the fuel pressure is not reasonable when compared to the fuel pressure reading shown in Cat ET.
Repair: Replace the pressure sensor. Reset all active codes and clear all logged codes by cycling the keyswitch to the OFF position.
If the problem is not resolved, proceed to Test Step 3.
3. Inspect the Fuel Lines
A. Visually inspect the fuel lines. Also, inspect the fuel cooler, if equipped.
B. Inspect the fuel lines for the following:
- Restrictions
- Pinching
- Swelling
Fuel Lines
Result: The fuel lines and the cooler (if equipped) are OK.
Proceed to Test Step 4.
Result: The fuel lines and the cooler (if equipped) are NOT OK.
Repair: Make the necessary repairs. Reset all active codes and clear all logged codes by cycling the keyswitch to the OFF position.
If the problem is not resolved, proceed to Test Step 4.
4. Replace the Fuel Pressure Regulator
Pressure Regulator
Result: The regulator was replaced. Reset all active codes and clear all logged codes by cycling the keyswitch to the OFF position.
If the problem is not resolved, proceed to Test Step 5.
5. Inspect the Relief Valve for the Transfer Pump
Note: The spring must move freely.
Relief Valve
Result: The relief valve is stuck CLOSED.
Repair: Replace the fuel transfer pump. Reset all active codes and clear all logged codes by cycling the keyswitch to the OFF position.
Verify that the repair eliminated the problem.
Result: The relief valve is OK.
Clean the relief valve and reinstall the relief valve. Reset all active codes and clear all logged codes by cycling the keyswitch to the OFF position.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts tilt Honda:

56000-ZW9-W53
 
56000-ZW9-W53 TILT ASSY., POWER
BF9.9D4 SRTA, BF9.9D5 SRTA, BF9.9D6 SRTA, BFP8D4 LHTA, BFP8D4 LRTA, BFP8D5 LHTA, BFP8D5 LRTA, BFP8D6 LHTA, BFP8D6 LRTA, BFP8DK0 LHTA, BFP8DK0 LRTA, BFP8DK2 LHTA, BFP8DK2 LRTA, BFP8DK3 LHTA, BFP8DK3 LRTA, BFP9.9D4 LHTA, BFP9.9D4 LRTA, BFP9.9D4 XHTA, B
Back to top