15723-ZV0-010 Honda TUBE B, BREATHER (Honda Code 5774088).


15723-ZV0-010 TUBE B, BREATHER (Honda Code 5774088). Honda BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB TUBE
15723-ZV0-010 TUBE B, BREATHER (Honda Code 5774088). Honda
Rating:
93

Buy TUBE B, BREATHER (Honda Code 5774088). 15723-ZV0-010 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Compatible models:

Honda entire parts catalog list:

BF2AM SA 1997
BF2AM SAB 1997
BF2AW LA 1998
BF2AW SA 1998
BF2AW SAB 1998

Information:


Illustration 1 g01635994
Illustration 2 g01636024
(25) Boost pressure (30) + 5 VDC (35) Analog return
Table 1
Diagnostic Code    
Code and Description    Flash Code    Default Conditions which Generate this Code    System Response    
102 -00 Boost Pressure Sensor : High     25     The boost pressure signal voltage is valid, but above normal.     The diagnostic code is logged. Also, the engine power is limited. boost pressure is set to
600 kPa (87 psi).    
102-01 Boost Pressure Sensor : Low     25     The boost pressure signal voltage is valid, but below normal.     The diagnostic code is logged. Also, the engine power is limited. boost pressure is set to
600 kPa (87 psi).    
102-03 Boost Pressure Sensor : Voltage Above Normal     25     The boost pressure signal voltage is greater than 5.0 VDC.     The diagnostic code is logged. Also, the engine power is limited. boost pressure is set to
600 kPa (87 psi).    
102-04 Boost Pressure Sensor : Voltage Below Normal     25     The boost pressure signal voltage is less than 0.75 VDC.     The diagnostic code is logged. Also, the engine power is limited. boost pressure is set to
600 kPa (87 psi).    
102-13 Boost Pressure Sensor : Calibration Required     42     The boost pressure sensor is not calibrated.     The fault is active and the ECM converts to low power. Also, boost pressure is set to
0 kPa (0 psi).    Test Step 1. Inspect Electrical Connectors and Wiring
Turn the engine control switch to the OFF position.
Thoroughly inspect the J14/P14 connector, and the J8/P8 connector. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the inlet manifold pressure sensor.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Check the harness for abrasions and for pinch points from the battery to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points. Proceed to Test Step 2.
NOT OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Open or Short Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Turn the engine control switch to the ON position.
Check for active diagnostic codes 102-03 or 102-04.Expected Result:No active diagnostic codes exist.Results:
OK - No active diagnostic codes exist. Proceed to Test Step 3.
NOT OK - Diagnostic codes 102-03 or 102-04 are present.Repair: Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test.".STOPTest Step 3. Calibrate the Boost Sensor
Connect Cat ET to the Service Tool Connector.
Turn the engine control switch to the ON position.
Select the boost sensor calibration screen.
The calibration will take several seconds. Expected Result:The screen will display "Calibrated" when the calibration is complete.Results:
OK - The screen displays "Calibrated" when the calibration is complete. Proceed to Test Step 4.
NOT OK - The screen does not display "Calibrated" when the calibration is complete. Proceed to Test Step 5.Test Step 4. Boost Pressure Sensor Test
Remove the sensor from the engine.
Connect the FT-1906 Air Test Kit to the sensor.
Connect to the service tool connector.
Turn the engine control switch to the ON position.
Close the valve on the test kit and apply 100 kPa (14.5 psi) to the sensor.
Observe the display on Cat ET.Note: The leakage rate should not exceed 20 kPa (3 psi) in 30 seconds. Expected Result:Cat ET displays 0 20 kPa (0 3 psi) when pressure is not applied. Cat ET displays 100 20 kPa (14.5 3 psi) when pressure is applied.Results:
OK - Cat ET displays 0 20 kPa (0 3 psi) when pressure is not applied. Cat ET displays 100 20 kPa (14.5 3 psi) when pressure is applied.Repair: The boost sensor is working properly. For a intermittent problem, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
NOT OK - Cat ET does not display 0 20 kPa (0 3 psi) when pressure is not applied. Cat ET does not display 100 20 kPa (14.5 3 psi) when pressure is applied. Proceed to Test Step 5.Test Step 5. Check Supply Voltage at the Sensor
Turn the engine control switch to the ON position.
Measure the voltage between P8-A and P8-B.Expected Result:The voltage measures 5.0 0.25 VDC.Results:
OK - The voltage measures 5.0 0.25 VDC. Proceed to Test Step 7.
NOT OK - The voltage does not measure 5.0 0.25 VDC. Proceed to Test Step 6.Test Step 6. Check Supply Voltage at the ECM
Turn the engine control switch to the ON position.
Measure the voltage between P14-30 and P14-35.Expected Result:The voltage measures 5.0 0.25 VDC.Results:
OK - The voltage measures 5.0 0.25 VDC.Repair: The fault is in the wiring harness. Repair the harness or replace the harness.STOP
NOT OK - The voltage does not measure 5.0 0.25 VDC.Repair: The fault is in the ECM. Replace the ECM.STOPTest Step 7. Check Signal Voltage at the Sensor
Turn the engine control switch to the ON position.
Measure the voltage between P8-C and P8-B.Expected Result:The voltage measurement is between 0.4 VDC and 4.4 VDC.Results:
OK - The voltage measurement is between 0.4 VDC and 4.4 VDC. Proceed to Test Step 8.
NOT OK - The voltage measurement is not between 0.4 VDC and 4.4 VDC.Repair: Replace the sensor.STOPTest Step 8. Check Signal Voltage at the ECM
Turn the engine control switch to the ON position.
Measure the voltage between P14-25 andP14-35.Expected Result:The voltage measurement is between 0.4 VDC and 4.4 VDC.Results:
OK - The voltage measureme


Parts tube Honda:

15722-ZV0-000
 
15722-ZV0-000 TUBE A, BREATHER (Honda Code 2133080).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB
15723-ZV0-000
19251-ZV0-000
TUBE, WATER (Honda Code 1814995).
19251-ZV0-000 TUBE, WATER (Honda Code 1814995).
BF2AM SA, BF2AM SAB, BF2AW SA, BF2AW SAB
17512-ZV0-000
 
17512-ZV0-000 TUBE, FUEL (Honda Code 1814664).
BF2AM SA, BF2AM SAB, BF2AW LA, BF2AW SA, BF2AW SAB
Back to top