19251-ZY9-000 Honda TUBE, WATER (L) (Honda Code 8576175).


19251-ZY9-000 TUBE, WATER (L) (Honda Code 8576175). Honda BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK2 LRTA TUBE
19251-ZY9-000 TUBE, WATER (L) (Honda Code 8576175). Honda
Rating:
8

Buy TUBE, WATER (L) (Honda Code 8576175). 19251-ZY9-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Honda entire parts catalog list:

BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK2 LRTA 2007

Information:

1. Disconnect six hoses to compressor (1), remove tube (2) and connect hoist to compressor.2. Remove bolts (3) that mount compressor (1) to the engine and remove compressor. The following steps are for installation of the air compressor.3. Position air compressor (1) and install bolts (3).4. Install tube (2) and connect six hoses to compressor (1).Disassemble Air Compressor
Start By:a. remove air compressorb. remove drive gear. 1. Remove the water line elbow, the air line elbows and oil (drain) tube from the air compressor.2. Remove bolts (1) from the cylinder head. Remove cylinder head (2) and the gasket from the crankcase.3. Remove inlet valve springs (7).4. Remove (discharge) valve seats (6) from the cylinder head. Remove valves (8) and springs (5).5. Inspect the valve seats for damage and wear. Make replacements if necessary. 6. Remove valve stops (9) as follows:a. Put the machined surface of the cylinder head down on an arbor press.b. Gradually push the stops from the top of the cylinder head and out of the bottom.c. Be sure there is enough clearance for the stops between the press and the bottom of the cylinder head.d. Inspect the stop bore in the cylinder head. Make a replacement of the head body if the bore is damaged. Remove the valve stops only if there is wear and damage, also if the valve movement (travel) exceeds 1.45 mm (.057 in.).7. Remove bolts (3) from the adapter. Remove adapters (4) from the compressor housing. 8. Remove O-ring seal (10), the thrust washer and the bearing from the adapter with tool (A).9. Remove bolts (12) from the cover. Remove cover (11) and the gasket from the crankcase. 10. Bend down the lock on lock straps (13). Remove bolts (14) from the bearing caps.11. Put identification on the bearing caps for correct installation with the connecting rod. Remove the bearing caps. 12. Remove pistons (15) from the crankcase through the top of the cylinders.13. Remove crankshaft (16) from the crankcase. Remove the key from the crankshaft. 14. Remove end cover (17) from the crankcase. Remove the O-ring seal, the thrust washer and the bearing.15. Remove cover (18), the gasket and the strainer from the air inlet opening. 16. Remove inlet valves (20) from their guides (21). Remove the inlet valve guides from around the inlet valve seats.
Be careful not to cause damage to the inlet valve seats.
17. Remove (unloader) spring (19), spring saddle (22) and the spring seat from the housing with needle nose pliers. 18. Remove (unloader) plunger (24) and guides (25) from the housing. Remove the guides from the plungers to plungers.19. To remove (unloader) pistons (23) from the bore, put a cover over the inlet port, then blow air pressure in the governor mounting pad (unloader) port. 20. Remove lockpin (27) that holds rod pin (26) in the piston. Remove the pin from connecting rod (28). 21. Remove the piston rings from piston (15). Remove two compression rings (29), the oil ring and the expander ring with tool (B).22. Remove the bearings from the connecting rod and the connecting rod cap. 23. Remove the piston pin bushing with tool (C).24. Remove the small seal rings from both ends of the housing.25. Clean all the oil passages through the housing, the crankshaft, the end cover and the adapter.Assemble Air Compressor
1. Check (unloaded) bore bushings (30) for damage and wear. If these bushings need replacement, remove the bushing by the use of a 3.18 mm (1/8 in.) pipe threaded tap. Then install a 3.18 mm (1/8 in.) pipe threaded rod, and pull the bushing straight up and out.2. Check the cylinder bores in the crankcase housing for damages (scored or out of round). Measure the cylinder bore in several places. If the measurement difference is more than 0.03 mm (.001 in.) or taper is more than 0.05 mm (.002 in.) the cylinder bore must be made larger (rebored or honed oversize). See Specifications.3. Install seal rings (32) in both ends of the crankcase housing.4. Install the new (unloader) pistons in their bore.
Be careful not to cause damage to the O-ring seals or the spiral rings.
5. Put the unloader plungers in their guides. Install the plunger and guide as a unit (33) to the crankcase housing and on top of the pistons. Install the unloader spring seat in the crankcase housing.6. Put saddle (22) in position between the unloader piston guides. Install (unloader) spring (19). Make sure it makes a seat on the spring seats and on the saddle.7. Install inlet valve guides (36) on (unloader) bore bushing (31) in the case housing. Put inlet valves (35) in the guides.8. Install strainer (34), the gasket and cover (18) over the air inlet port of the crankcase housing. Install the bolts that hold the cover. 9. Install bearing (37) in the cover with tooling (A). Make sure the groove in the bearing is in alignment with the oil hole in the cover. Install thrust washer (38) and O-ring seal (39).10. Put clean SAE 30 engine oil on the bearing and the seal. Install the end cover and the bolts that hold it to the crankcase housing.11. Install the crankcase in the crankcase housing and the end cover bearing. 12. Install the bearing in adapter with tooling (B). Install thrust washer (40) and O-ring seal (41) in the adapter.13. Put clean SAE 30 engine oil on the bearing and the O-ring seal. Install the adapter over the crankshaft and to the housing. Install the bolts that hold the adapter. Tighten the bolts to a torque of 38 to 45 lb.ft. (49 to 60 N m.). 14. Assemble the piston rings on the piston with tooling (C) as follows:a. Check piston ring (29) gaps. Check with the piston rings in the cylinder bore. The gap clearance must be 0.05 to 0.25 mm (.002 to .010 in.).b. Install expander ring (42) on the bottom groove of the piston. Install oil ring (29) over the expander ring. Expander and oil ring (29) must have a clearance


Parts tube Honda:

17701-ZV5-000
TUBE, FUEL (7.5X2000) (Honda Code 3702305).
17701-ZV5-000 TUBE, FUEL (7.5X2000) (Honda Code 3702305).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
17702-ZV4-000
TUBE, FUEL SHORT (Honda Code 2795557).
17702-ZV4-000 TUBE, FUEL SHORT (Honda Code 2795557).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
37202-ZW5-U01
TUBE, SPEEDOMETER (4X7X8000) (Honda Code 7702202).
37202-ZW5-U01 TUBE, SPEEDOMETER (4X7X8000) (Honda Code 7702202).
BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF115DK1 LA, BF115DK1 XA
17700-ZY3-010
TUBE ASSY., FUEL (JOINT TYPE) (Honda Code 7425796).
17700-ZY3-010 TUBE ASSY., FUEL (JOINT TYPE) (Honda Code 7425796).
BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF150A4 LA, BF150A4 XA, BF150A4 XCA, BF150A5 LA, BF150A5 XA, BF150A5 XCA, BF150A6 LA, BF150A6 XA, B
16197-ZY9-000
TUBE A, AIR VENT (Honda Code 8575698).
16197-ZY9-000 TUBE A, AIR VENT (Honda Code 8575698).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
16198-ZY9-000
TUBE B, AIR VENT (Honda Code 8575706).
16198-ZY9-000 TUBE B, AIR VENT (Honda Code 8575706).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
16199-ZY9-000
TUBE C, AIR VENT (Honda Code 8575714).
16199-ZY9-000 TUBE C, AIR VENT (Honda Code 8575714).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
16881-ZY9-010
TUBE D, FUEL (Honda Code 9127952).
16881-ZY9-010 TUBE D, FUEL (Honda Code 9127952).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
Back to top