14647-PWA-000 Honda WASHER, THRUST


14647-PWA-000 WASHER, THRUST Honda BF60AK1 LRTA, BF60AK1 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA WASHER
14647-PWA-000 WASHER, THRUST Honda
Rating:
18

Buy WASHER, THRUST 14647-PWA-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Honda entire parts catalog list:

BF60AK1 LRTA 2007
BF60AK1 XRTA 2007
BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BFP60AK1 LRTA 2007
BFP60AK1 LRTB 2007
BFP60AK1 XRTA 2007

Information:

1. Disconnect tube (1) from fuel ratio control (3).2. Remove two bolts (2) that hold the fuel ratio control to the governor.3. Disengage the shaft on the fuel ratio control from the lever in the governor. Remove fuel ratio control (3).4. To install the fuel ratio control, engage the fuel ratio control shaft in the lever inside the governor.5. Install bolts (2) and connect tube (1).Disassemble Fuel Ratio Control (Earlier)
Start By:a. remove fuel ratio control 1. Remove bolts (2) which hold cover (1) to housing (3). Be careful when bolts (2) are removed because cover (1) is under spring force. 2. Make a separation of the components of the fuel ratio control: cover (1), spring (4), valve (5), spring (6), retainer (7), spring (8), valve assembly (9) and housing (3). 3. Make a separation of the covers (1). 4. Remove nut (11) and stop (10) from the cover. 5. Remove nut (12) and make a separation of nut (12), washer (13), retainer (14), diaphragm (15), valve extension (17), spring (16) and valve (18). 6. Use tooling (A) to remove snap ring (19).7. Remove piston (20) from valve (18). 8. Remove seal (21) from piston (20).9. Inspect all parts and make replacements if necessary.Assemble Fuel Ratio Control (Earlier)
1. Put seal (21) on piston (20). Install the seal so the lip is toward the direction of the center of piston (20). 2. Put piston (20) on valve assembly (18).3. Use tooling (A) to put the snap ring (19) in position. 4. Put O-ring seal (22) in position on valve extension (17).5. Put diaphragm (15) on retainer (14). The outer lip of the diaphragm must be toward the hole with thread.6. Put engine oil on the seal (22) on valve extension (17) and put valve extension (17) into retainer (14). Install washer (13) and nut (12).7. Put spring (16) into valve extension (17) and engage internal valve (18) with hook on the valve extension (17).8. Put washer (23) on diaphragm (15). The flat side of washer (23) must be in contact with diaphragm (15). 9. Put stop (10) in cover (1). Put nut (11) on stop (10).10. Make a replacement of the gasket on cover (24). Put cover (24) on cover (1) and install the bolts which hold the covers together. 11. Put engine oil on the seal on valve assembly (9) and put valve assembly (9) into housing (3).12. Put spring (8) on valve assembly (9).13. Engage retainer (7) with spring (8). Put spring (6) into retainer (7).14. Put engine oil on valve (5) and put retainer (14) into housing (3). Engage internal valve (5) into valve assembly (9).15. Put spring (4) into the open face of the washer behind the diaphragm. 16. Put cover (1) against housing (3). Make sure the ring on the diaphragm is engaged with the groove in cover (1). Install bolts (2). Before installing the fuel ratio control, make adjustments according to Fuel Injection Test Bench, Special Instruction, Form No. SEHS7465-01.End By:a. install fuel ratio controlDisassemble And Assemble Fuel Ratio Control (Later)
Start By:a. remove fuel ratio control 1. Put tooling (A) in a vise so that the station (hole) being used is not over the vise jaw. Place the fuel ratio control over the pins in tooling (A). Remove bolts (3), and remove cover (24) and gasket (23).
There is spring force behind cover (6). Hold cover (6) in position, and slowly remove the bolts that hold it to release the spring force.
2. Remove bolts (5). Remove cover (6) from housing (9).3. Remove spring (7), washer (8), and diaphragm (20) from retainer (4). Remove retainer (4) from housing (9).4. Remove nut (2) from extension (18), and remove the extension from retainer (4). Remove valve (15), spring (21), and O-ring seal (22) from the extension.5. Remove spring (19) retainer (17), and spring (16) from housing (9).6. Remove piston (11) and valve assembly (13) from housing (9).7. Use tool (B), and remove snap ring (12) and washer (14) from valve assembly (13). Remove piston (11) from the valve assembly.8. Remove seal (10) from piston (11).9. If necessary, remove the stem portion from valve assembly (13).10. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. The following steps are for the assembly of the fuel ratio control.11. If removed during the disassembly, assemble the stem portion of valve assembly (13) to the valve using 9S3265 Retaining Compound.12. Lubricate seal (10) lightly with the lubricant being sealed. Put seal (10) on piston (11), and put piston (11) on valve assembly (13).13. Put washer (14) in position on valve assembly (13) and use tool (B) to install snap ring (12) on the valve assembly.14. Place housing (9) on tooling (A), and put tool (C) into the bore of the housing. Lubricate tool (C) with clean engine oil.15. Push piston (11) into position with a smooth swift motion. Remove tool (C) from housing (9). Place spring (16), retainer (17), and spring (16) in the housing.16. Put O-ring seal (22) on extension (18). Put spring (21) and valve (15) in position on the extension.17. Lubricate the bore of retainer (4), and O-ring seal (22) with clean engine oil. Install extension (18) in retainer (4). Install nut (2) on the extension.18. Put diaphragm (20), washer (8), and spring (7) in position on retainer (4). Install retainer (4) in housing (9).19. Hold retainer (4) in position, and install cover (6) to housing (9). Install bolts (5) that hold the cover.20. Make a replacement of gasket (23), and install the gasket and cover (24) with bolts (3). Tighten the bolts to a torque of 6- 12 3 N m (4-9 2 lb.ft.).End By:a. install fuel ratio control


Parts washer Honda:

90504-921-010
WASHER, PLAIN (6MM) (Honda Code 0285114).
90504-921-010 WASHER, PLAIN (6MM) (Honda Code 0285114).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90507-ZV4-000
WASHER, PLAIN (8MM) (Honda Code 2800613).
90507-ZV4-000 WASHER, PLAIN (8MM) (Honda Code 2800613).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90504-ZV5-000
WASHER, THRUST (34MM) (Honda Code 3706207).
90504-ZV5-000 WASHER, THRUST (34MM) (Honda Code 3706207).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90501-ZW1-710
WASHER (26MM) (Honda Code 4901120).
90501-ZW1-710 WASHER (26MM) (Honda Code 4901120).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 XA, BF115A2 XCA, BF115A3 XA, BF115A3 XCA, BF115A4 XA, BF115A4 XCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 XA, BF115A6 XCA, BF115AK0 XA, BF115AX XA, BF115AX XCA, BF115AY LA, BF115AY XA, B
90506-ZW1-B00
WASHER, PROPELLER THRUST (Honda Code 5743869).
90506-ZW1-B00 WASHER, PROPELLER THRUST (Honda Code 5743869).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90502-ZW4-H01
WASHER (8MM) (Honda Code 7759350).
90502-ZW4-H01 WASHER (8MM) (Honda Code 7759350).
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
90503-ZZ3-A41
WASHER, PLATE
90503-ZZ3-A41 WASHER, PLATE
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
90508-ZY9-000
WASHER (14MM)
90508-ZY9-000 WASHER (14MM)
BF60AK1 LRTA, BF60AK1 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
Back to top