90508-ZW1-003 Honda WASHER, TAB (Honda Code 4856357).

Table 1
Diagnostic Codes Table
J1939 Code and Description Conditions which Generate this Code System Response
110-17
Engine Coolant Temperature : Low - least severe (1) The temperature of the engine coolant has fallen below the trip point for the programmed delay time. The code is logged.
The ECM may derate the engine or shutdown the engine.
110-18
Engine Coolant Temperature : Low - moderate severity (2)
110-1
Engine Coolant Temperature : Low - most severe (3) Probable Causes
Ambient temperatures (if applicable)
Loads (if applicable)
Engine speed
Cooling fan (if applicable)
Water temperature regulator
Auxiliary coolant heater (if equipped)
Temperature sensorRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 2
Troubleshooting Test Steps Values Results
1. Extreme Ambient Temperatures (if applicable)
Extreme ambient temperature can cause overcooling.
Extreme Ambient Temperatures
Result: Ambient temperatures are extreme.
Repair: Install winter covers.
Verify that the repair eliminates the problem.
Result: Ambient temperatures are not extreme.
Proceed to Test Step 2.
2. Check the Load Factor (if applicable)
Light loads can cause overcooling. This overcooling is caused by the low heat input of the engine.
Light Loads
Result: Engine is operating under a light load.
Repair: Increase load factor if possible.
Verify that the repair eliminates the problem.
Result: Engine is not operating under a light load.
Proceed to Test Step 3.
3. Check for Low Engine Speed
Low engine speed can cause overcooling.
Low Engine Speed
Result: Engine is running at a low speed.
Repair: Increase engine speed if possible.
Verify that the repair eliminates the problem.
Result: Engine is not running at a low speed.
Proceed to Test Step 4.
4. The Cooling Fan is Always On (if applicable)
If the cooling fan is always on, overcooling can occur.
Fan
Result: The cooling fan is always on.
Repair: Resolve the issue.
Verify that the repair eliminates the problem.
Result: The cooling fan is not always on.
Proceed to Test Step 5.
5. Water Temperature Regulator
A regulator that is stuck open can cause overcooling.
A. Test the water temperature regulator according to Testing and Adjusting, "Water Temperature Regulator - Test".
B. Make sure that the proper water temperature regulator is installed. Refer to the Specifications manual for the correct water temperature regulator.
Water Temperature Regulator
Result: The regulator is stuck open or not installed.
Repair: Replace the regulator.
Verify that the repair eliminates the problem.
Result: The regulator not is stuck open is installed.
Proceed to Test Step 6.
6. Check the Auxiliary Coolant Heater (if equipped)
A malfunctioning auxiliary coolant heater can cause low coolant temperature.
A. Determine if the engine is equipped with an auxiliary coolant heater.
B. Check the heater for proper operation.
Auxiliary Coolant Heater
Result: The coolant heater is not operating properly.
Repair: Replace the heater.
Verify that the repair eliminates the problem.
Result: The coolant heater is working properly.
Proceed to Test Step 7.
7. Faulty Coolant Temperature Sensor and/or Circuit
A. Check the reading of the coolant temperature on the Cat ET. The temperature should rise steadily as the engine is warmed. Ensure that the temperature is reasonable.
Faulty Sensor or Circuit
Result: The coolant temperature is not reasonable.
Repair: Troubleshoot the circuit and the coolant temperature sensor. Refer to Troubleshooting, "Sensor Signal (Analog, Passive) - Test".
Verify that the repair eliminates the problem.
Result: The coolant temperature is reasonable.
STOP
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).