0378931 JOHNSON ACCESSORY,Carrying handle kit


0378931 ACCESSORY,Carrying handle kit JOHNSON 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40ES69R, 40R69R, RD-30A, RDS-30A, RK-30A, RX-16M, V4A-20A, V4S-20A ACCESSORY
0378931 ACCESSORY,Carrying handle kit JOHNSON
Rating:
88

Buy ACCESSORY,Carrying handle kit 0378931 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.99
 

27-11-2021

-: -
OMC Carry Handle P/N 378931 0378931 NOS
Number on catalog scheme: 37893
 

BRP JOHNSON entire parts catalog list:

33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E70M, 33EL70M, 33R70M, 33RL70M 1970
33E70M, 33EL70M, 33R70M, 33RL70M 1970
40E69R, 40EL69R 1969
40ES69R, 40ESL69R 1969
40R69R, 40RL69R 1969
RD-30A, RD-30D, RD-30S, RDL-30A, RDL-30D, RDL-30S 1968
RDS-30A, RDS-30C, RDS-30D, RDS-30S, RDSL-30A, RDSL-30C, RDSL-30D, RDSL-30S 1968
RK-30A, RK-30C, RK-30D, RKL-30A, RKL-30C, RKL-30D 1968
RX-16M, RX-16R, RXE-16M, RXE-16R, RXEL-16M, RXEL-16R, RXL-16M, RXL-16R 1968
V4A-20A, V4AL-20A 1968
V4S-20A, V4SL-20A 1968

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Puller 1
126-7183 Crossblock 1
126-7177 Puller Legs 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Remove the auxiliary equipment from the accessory drive housing. Refer to the Original Equipment Manufacture (OEM) for the correct procedure.
Illustration 1 g02186453
Illustration 2 g02374996
If the OEM driven equipment has not been installed to the auxiliary drive, remove bolts (1). Remove cover plate (2) and remove gasket (3) (not shown).
Remove allen head screws (4) from accessory drive housing (5). Remove allen head screw (6) from accessory drive housing (5).
Remove accessory drive housing (5) from the front housing.
Remove gasket (7) from accessory drive housing (5).
Illustration 3 g02374997
If necessary, follow Step 6a through Step 6d to disassemble the accessory drive.
Remove circlip (11) from gear (9).
Remove circlip (12) from accessory drive housing (5).
Place accessory drive housing (5) onto a suitable support. Press the assembly of gear (9) and bearing (10) out of accessory drive housing (5). Use Tooling (A) to remove bearing (10) from gear (9).Note: Note the position of the bearing in the accessory drive housing before removal.
Press bearing (8) out of accessory drive housing (5).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 7M-7456 Bearing Mount Compound 1
C - Rubber Grease 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g02374997
Illustration 5 g02052174
Illustration 6 g02052273
If necessary, follow Step 1a through Step 1f to assemble the accessory drive.
Inspect the condition of the teeth and the splines of gear (9) for wear and damage. Inspect bearing (8), bearing (10), circlip (11), and circlip (12). Inspect the front housing for wear and damage. Replace any components that are worn or damaged.
Apply a small continuous bead of Tooling (B) to outer Surface (X) of bearing (8). Place the accessory drive housing on a suitable support. Press the outer race of bearing (8) until the bearing is in the correct position within accessory drive housing (5). Remove any excess bearing mount compound.
Apply a small continuous bead of Tooling (B) to inner Surface (Y) of bearing (10). Place the inner race of bearing (10) onto a suitable support. Press the shaft of gear (9) into bearing (10) until the shoulder of the gear is against the bearing. Remove any excess bearing mount compound.
Install circlip (11) into the groove in gear (9).
Apply a small continuous bead of Tooling (B) to the outer Surface (Z) of bearing (10). Place accessory drive housing (5) on a suitable support. Ensure that the shaft of gear (9) is correctly aligned with bearing (8). Press the assembly of the gear into the accessory drive housing. Remove any excess bearing mount compound.
Install circlip (12) into t


Parts accessory JOHNSON:

0379778
 
0379778 ACCESSORY,Shorting switch extension kit
33E69A, 33E69A, 33E70M, 33E70M, 40R69R, RD-30A, RX-16M
0377949
 
0377949 ACCESSORY,Steering handle kit
33E69A, 33E69A, 33E70M, 33E70M, 40R69R, RD-30A, RX-16M
Back to top