0330697 JOHNSON ADAPTER, Exhaust housing


0330697 ADAPTER, Exhaust housing JOHNSON J60ELCDS, J60ELCUC, J65RWLCDR, J65RWLCOC, J65WMLCDR, J65WMLCOC, J70ELCOS, J75ECDC, J75ECOS, J75ECUR ADAPTER
0330697 ADAPTER, Exhaust housing JOHNSON
Rating:
68

Buy ADAPTER, Exhaust housing 0330697 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

BRP JOHNSON entire parts catalog list:

J60ELCDS, J60TLCDS 1986
J60ELCUC, J60TLCUC 1987
J65RWLCDR, J65TELCDR 1986
J65RWLCOC, J65TELCOC 1985
J65WMLCDR 1986
J65WMLCOC, J65WTLCOC 1985
J70ELCOS, J70TLCOS 1985
J75ECDC 1986
J75ECOS 1985
J75ECUR 1987

Information:

Type 1 Fuel Filters
Illustration 1 g02791865
Typical example
Loosen the vent screw (1) on the secondary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent screw (1) to a torque of 20 N m (15 lb ft)
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cycle the throttle lever from the low idle position to the high idle position three times. The cycle time for the throttle lever is one second to 6 seconds for one complete cycle.Note: To purge air from the fuel injection pump on engines with a fixed throttle, the engine should be run at full load for 30 seconds. The load should then be decreased until the engine is at high idle. This should be repeated three times. This will assist in removing trapped air from the fuel injection pump.
Check for leaks in the fuel system.Type 2 Fuel Filters
Illustration 2 g03651564
Typical example
Loosen the vent plug (1) on the primary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent plug (1) .
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cycle the throttle lever from the low idle position to the high idle position three times. The cycle time for the throttle lever is one second to 6 seconds for one complete cycle.Note: To purge air from the fuel injection pump on engines with a fixed throttle, the engine should be run at full load for 30 seconds. The load should then be decreased until the engine is at high idle. This should be repeated three times. This will assist in removing trapped air from the fuel injection pump.
Check for leaks in the fuel system.


Parts adapter JOHNSON:

0321638
 
0321638 ADAPTER,Exhaust housing
70EL76D, 70EL77S, 70EL78C, 70EL79R, 75ELR76D, 75ELR77S, 75ELR78C, 75ELR79R, J60ELCDS, J60ELCUC, J70ELCIH, J70ELCNB, J70ELCOS, J70ELCRD, J70ELCSA, J70ELCTE, J75ECCA, J75ECDC, J75ECNB, J75ECOS, J75ECRD, J75ECTE, J75ECUR, J75ERCIH, J75ERCSA
0387584
 
0387584 ADAPTER FITTING & NUT PACKAGE
100ML79S, 115ETZ78C, 115ML79R, 115TXL77S, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 85ETLR78C, 85ML79R, 85TXLR77S, J100MLCSC, J100WMLCDR, J100WMLCOC, J1
0123470
 
0123470 ADAPTER, Fitting
J65RWLCRS, J65WMLCOC
Back to top