0336299 ADJUSTER JOHNSON
BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, BJ70PLEEE, BJ70PLSIS, BJ70PLSSD, J40JPLEEC, J40JPLSIA, J40JPLSSR, J50DTLECA, J50DTLEOS, J60ELEIB, J60ELENE, J60ELEOC, J60ELERS, J60ELETD, J60PLEEB, J60PLSID, J6
ADJUSTER
Price: query
Rating:
Compatible models:
BJ50DTLEDC
BJ50DTLEUR
BJ60ELEDR
BJ60ELEUA
BJ60TLECM
BJ70ELECB
BJ70ELEDA
BJ70ELEUM
BJ70PLEEE
BJ70PLSIS
BJ70PLSSD
J40JPLEEC
J40JPLSIA
J40JPLSSR
J50DTLECA
J50DTLEOS
J60ELEIB
J60ELENE
J60ELEOC
J60ELERS
J60ELETD
J60PLEEB
J60PLSID
J60PLSSE
J65WELEES
J65WELSIR
J65WELSSC
J65WMLEIB
J65WMLENE
J65WMLEOC
J65WMLERS
J65WMLETD
J70ELEIE
J70ELEND
J70ELEOR
J70ELERC
J70ELETS
SJ65WMLD
SJ65WMLM
SJ65WMLZ2
JOHNSON
BRP JOHNSON entire parts catalog list:
BJ50DTLEUR, J50DTLEUR, J50ELEUR 1997
BJ60ELEDR, BJ60TLEDR, J60ELEDR, J60TLEDR, SJ60TLEDR 1996
BJ60ELEUA, BJ60TLEUA, J60ELEUA, J60TLEUA 1997
BJ60TLECM, J60TLECM 1998
BJ70ELECB, BJ70TLECB, J70TLECB 1998
BJ70ELEDA, BJ70TLEDA, HJ70TXEDA, J70TLEDA, SJ70TLEDA 1996
BJ70ELEUM, BJ70TLEUM, HJ70TXEUM, J70TLEUM 1997
BJ70PLEEE, J70PLEEE 1999
BJ70PLSIS, J70PLSIS, J70VLSIS, RJ70PLSIS 2001
BJ70PLSSD, J70PLSSD, RJ70PLSSD 2000
J40JPLEEC 1999
J40JPLSIA, J40JVLSIA 2001
J40JPLSSR 2000
J50DTLECA 1998
J50DTLEOS, J50ELEOS 1995
J60ELEIB, J60TLEIB, TJ60TLEIB, VJ60ELEIB, VJ60TLEIB 1991
J60ELENE, J60TLENE, TJ60TLENE, VJ60ELENE, VJ60TLENE 1992
J60ELEOC, J60TLEOC 1995
J60ELERS, J60ELERV, J60TLERS, J60TLERV 1994
J60ELETD, J60TLETD, TJ60TLETD, VJ60ELETD 1993
J60PLEEB 1999
J60PLSID, J60VLSID 2001
J60PLSSE 2000
J65WELEES 1999
J65WELSIR 2001
J65WELSSC 2000
J65WMLEIB 1991
J65WMLENE 1992
J65WMLEOC 1995
J65WMLERS 1994
J65WMLETD 1993
J70ELEIE, J70TLEIE, VJ70ELEIE, VJ70TLEIE 1991
J70ELEND, J70TLEND, VJ70ELEND, VJ70TLEND 1992
J70ELEOR, J70JLEOS, J70TLEOR 1995
J70ELERC, J70ELERV, J70TLERC, J70TLERV 1994
J70ELETS, J70TLETS, VJ70ELETS, VJ70TLETS 1993
SJ65WMLD, SJ65WMYD 1998
SJ65WMLM, SJ65WMYM 1996
SJ65WMLZ2, SJ65WMYZ2 1997
Information:
2. Remove four bolts (1) and elbow (2). 3. Check the condition of O-ring seal (3). Use a new part for replacement if O-ring seal (3) is worn or damaged. 4. Remove bolts (4) from the timing gear cover and remove water pump. Remove water pump.
Typical Example5. Check the condition of O-ring seal (5). Use a new part for replacement if O-ring seal (5) is worn or damaged.6. Install the water pump in the reverse order of removal.End by:a. Install the oil cooler and oil filter base.b. Install the water temperature regulator and manifold.c. Fill with coolant **Refer to the Operation and Maintenance Manual for additional information.Disassemble & Assemble Water Pump
Start by:a. Remove water pump. The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) and washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14) and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10) and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal counter bore in the pump housing.10. Install bearing (9), spacer (10) and bearing (11) on shaft (13).11. Put retainer (12) and gear (17) on shaft assembly. Install retainer (14) and bolt (15) on the shaft.12. Use tooling (B) to install lip-type seal (8) in housing (7). Install seal with the lip toward the inside of the housing. Put a small amount of clean engine oil on the lip of the seal.13. Install a new O-ring seal (18) on the housing.14. Put gear and shaft assembly (17) in position in the housing. Install bolts (16) that hold retainer (12) to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (20) in position in seal (19). Use hand pressure and tool (C) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation. Assemble using water as a lubricant.16. Separate spring from seal (5). Use hand pressure and tool (C) to install the seal on the shaft of gear and shaft assembly (17). Push the seal on the shaft until the seal faces make light contact. Install the spring on the shaft.17. Put impeller (6) in position on the shaft. Install washer (2) and bolt (1) that hold the impeller. Tighten the bolt to a torque of 39 3 N m (28 2 lb ft).18. Install the O-ring seal on the outside diameter of adapter (4). Put a small amount of clean SAE 30 oil on the O-ring seal.19. Install O-ring seal (3) on the adapter.20. Put adapter (4) in position on the housing.End by:a. Install water pump.
Typical Example5. Check the condition of O-ring seal (5). Use a new part for replacement if O-ring seal (5) is worn or damaged.6. Install the water pump in the reverse order of removal.End by:a. Install the oil cooler and oil filter base.b. Install the water temperature regulator and manifold.c. Fill with coolant **Refer to the Operation and Maintenance Manual for additional information.Disassemble & Assemble Water Pump
Start by:a. Remove water pump. The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) and washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14) and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10) and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal counter bore in the pump housing.10. Install bearing (9), spacer (10) and bearing (11) on shaft (13).11. Put retainer (12) and gear (17) on shaft assembly. Install retainer (14) and bolt (15) on the shaft.12. Use tooling (B) to install lip-type seal (8) in housing (7). Install seal with the lip toward the inside of the housing. Put a small amount of clean engine oil on the lip of the seal.13. Install a new O-ring seal (18) on the housing.14. Put gear and shaft assembly (17) in position in the housing. Install bolts (16) that hold retainer (12) to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (20) in position in seal (19). Use hand pressure and tool (C) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation. Assemble using water as a lubricant.16. Separate spring from seal (5). Use hand pressure and tool (C) to install the seal on the shaft of gear and shaft assembly (17). Push the seal on the shaft until the seal faces make light contact. Install the spring on the shaft.17. Put impeller (6) in position on the shaft. Install washer (2) and bolt (1) that hold the impeller. Tighten the bolt to a torque of 39 3 N m (28 2 lb ft).18. Install the O-ring seal on the outside diameter of adapter (4). Put a small amount of clean SAE 30 oil on the O-ring seal.19. Install O-ring seal (3) on the adapter.20. Put adapter (4) in position on the housing.End by:a. Install water pump.