0209493 JOHNSON APPLIQUE,Evinrude,stbd. & port


0209493 APPLIQUE,Evinrude,stbd. & port JOHNSON J150TLCRD, J150TLCTB, J175TLCTD, J185TLCRS, J200TLCTD, J235TLCRC, J235TLCTD APPLIQUE
0209493 APPLIQUE,Evinrude,stbd. & port JOHNSON
Rating:
23

Buy APPLIQUE,Evinrude,stbd. & port 0209493 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

BRP JOHNSON entire parts catalog list:

J150TLCRD, J150TXCRD 1984
J150TLCTB, J150TLCTE, J150TXCTB, J150TXCTE 1983
J175TLCTD, J175TLCTE, J175TXCTD, J175TXCTE 1983
J185TLCRS, J185TXCR 1984
J200TLCTD, J200TLCTS, J200TXCTD, J200TXCTS 1983
J235TLCRC, J235TXCRC 1984
J235TLCTD, J235TLCTS, J235TXCTD, J235TXCTS 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Retaining Ring Pliers 1
B - Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g06360971
Illustration 2 g02090036Note: If the original piston rings are to be refitted, ensure that the piston rings are refitted in the original orientation and positions.
If the original piston is assembled, follow Step 2a through Step 2e to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position and use Tooling (B) to install oil control ring (3) over the piston and the spring.Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at 120 degrees away from each other.Note: A new piston assembly is supplied with new piston rings.
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar distributor.
If connecting rod assembly (6), the bush for piston pin (7), connecting rod cap (11), and bolts (12) or the bush for piston pin (7) is replaced, refer to Specifications, "Connecting Rods" for further information.
Illustration 3 g02514164
Positioning of the upper and lower bearing shell.
Lubricate the bush for piston pin (7) in connecting rod (6) with clean engine oil.
Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Illustration 4 g06361258
Place piston (4) on a suitable surface with the crown downward. Position connecting rod (6) with the forged Mark (X) to the square (13) on the piston.
Install piston pin (7) to piston (4).Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) to install circlips (5) to the piston pin bore in piston (4).Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (6). Ensure that the bearing is centralized in the connecting rod cap. Refer to Illustration 3.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the bearing is centralized in the connecting rod. Refer to Illustration 3.
Repeat Step 2 through Step 10 for the remaining piston and connecting rod assemblies.Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the assembly procedure for the piston and connecting rod is completed, carry out the installation procedure as soon as possible. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts applique JOHNSON:

0327490
 
0327490 APPLIQUE
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLESB, J100WMLCDR, J100WMLCOC, J100WMLCRS, J100WTLCUA, J100WTLESM, J100WTLZ, J10EESC, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115MLCNB, J115MLCOS, J115MLCRD,
0327851
 
0327851 APPLIQUE
J115MLCTE, J140MLCTE, J150TLCTB, J175TLCTD, J200TLCTD, J235TLCTD, J70ELCTE, J75ECTE, J90MLCTE
0209492
 
0209492 APPLIQUE,Front
J150TLCOS, J150TLCRD, J150TLCTB, J175TLCOC, J175TLCTD, J185TLCOC, J185TLCRS, J200TLCTD, J235TLCOR, J235TLCRC, J235TLCTD, J70ELCOS, J75ECOS
0328937
 
0328937 APPLIQUE, Rear
J115MLCRD, J140TLCRD, J150TLCRD, J185TLCRS, J20CRCOS, J235TLCRC, J25ECOC, J30ECOA, J40ECOB, J40ECRM, J50BECOB, J60ELCOD, J70ELCRD, J75ECRD, J90MLCRD
0209859
 
0209859 APPLIQUE, Engine cover, rear, 150
J150TLCRD, J185TLCRS, J235TLCRC
0209863
 
0209863 APPLIQUE, Engine cover, rear, 235
J150TLCRD, J185TLCRS, J235TLCRC
0210032
APPLIQUE, Engine cover, rear, 185
0210032 APPLIQUE, Engine cover, rear, 185
J150TLCRD, J185TLCRS, J235TLCRC
0328942
 
0328942 APPLIQUE, Engine cover, rear
J150TLCRD, J185TLCRS, J235TLCRC, J40ECOB
Back to top