0210505 APPLIQUE, Front JOHNSON
CJ300TLCDC, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA
APPLIQUE
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER - EVINRUDE » 0210505
J275CXCCA, J275PLCCA, J275PXCCA 1988
J300CLCUR, J300CXCUR, J300PLCUR, J300PXCUR 1987
J300CXCCA, J300PLCCA, J300PXCCA 1988
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Shaft Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check" for the correct procedure. Note: The air compressor must be timed with the engine in order to minimize engine vibration.
Illustration 1 g02418379
Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g02418397
Slide hose clamps for coolant hose (3) and coolant hose (4) along the hose assemblies.
Disconnect coolant hose (3) and coolant hose (4) from the connections on air compressor (6).
Disconnect the air line from port (5) (not shown) and air line from port (7). Refer to the OEM for the correct procedure.
Illustration 3 g02418398
Illustration 4 g02420556
Illustration 5 g02418399
Remove banjo bolt (9) and remove sealing washers (10) (not shown).
Remove bolt (13) and bolt (15) from support bracket (14). Remove support bracket (14) from compressor (6) and the cylinder block.
Support air compressor (6). Remove nuts (18) and remove the air compressor from front housing (8).
If necessary, follow Step 13.a through Step 13.b in order to remove the hose assembly.
Make a temporary mark in order to identify the position of hose assembly (11).
Disconnect nut (12) and remove hose assembly (11).
If necessary, remove studs (17) from front housing (8).
If necessary, remove bolts (20) and remove plate (19). Remove O-ring seal (16) from plate (19). Refer to Illustration 5.
Parts applique JOHNSON:
0327490
0327490 APPLIQUE
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLESB, J100WMLCDR, J100WMLCOC, J100WMLCRS, J100WTLCUA, J100WTLESM, J100WTLZ, J10EESC, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115MLCNB, J115MLCOS, J115MLCRD,
0330084
0330086
0330086 APPLIQUE, V, front & rear
CJ300TLCDC, CJ300TLCOS, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXESB
0330076
0330076 APPLIQUE, Rear
CJ300TLCDC, CJ300TLCOS, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXESB
0330088
0330088 APPLIQUE, Front & rear
CJ300TLCDC, CJ300TLCOS, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXESB
0123315
0123315 APPLIQUE
J120TLAEM, J120TLASB, J120TLCCA, J140CXCCS, J140CXCEC, J140CXESR, J150CXCCA, J150CXCEM, J150CXESB, J175STLACM, J175STLCEB, J175STLESE, J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS, J275CXCCA, J28ELCDS, J28ELC
0210411
0210411 APPLIQUE, V-8, front
CJ275TLCDC, CJ300TLCDC, J250CXEIE, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXEIE, J300CXESB
0210415
0210415 APPLIQUE, Port & stbd.
CJ275TLCDC, CJ300TLCDC, J250CXEIE, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXEIE, J300CXESB