0389597 JOHNSON APPLIQUE


0389597 APPLIQUE JOHNSON 100ML79S, 115ML79R, 140ML79R, 70EL79R, 75ELR79R, 85ML79R APPLIQUE
0389597 APPLIQUE JOHNSON
Rating:
48

Buy APPLIQUE 0389597 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

BRP JOHNSON entire parts catalog list:

100ML79S, 100TLR79S, 100TXLR79S 1979
115ML79R, 115TL79R, 115TXL79R 1979
140ML79R, 140TL79R, 140TXL79R 1979
70EL79R 1979
75ELR79R, 75ER79R 1979
85ML79R, 85TL79R, 85TXL79R 1979

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     FT-2398     Oil Pump Shaft Tool     1    
0S-1627 Bolts     2    
2J-3506 Full Nuts     2    
B     1P-0510     Driver Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00551222
Note: On the lower bearing, align the hole in the bearing with the hole in the oil pump's body.
Put a coat of clean engine oil on the outside of each bearing. Use Tooling (B) and a press in order to install bearings (1) into the oil pump body. Install the bearings 12.30 0.25 mm (0.484 0.010 inch) below the surface of the oil pump body. The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 2 g00551223
Put a coat of clean engine oil on the outside of each bearing. Use Tooling (B) and a press in order to install bearings (3) into oil pump cover (4) . Align the hole in the bearing with the hole in the cover. Install the bearings 7.50 0.25 mm (0.230 0.010 inch) below the surface of the oil pump body. The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 3 g00551224
Ensure that dowels (9) are installed to a height of 12 1 mm (0.47 0.04 inch).
Put O-ring seal (5) and six O-ring seals (8) in position on cover (4) . Put clean engine oil on the seals.
Put a coat of clean engine oil on the bearings and the gear pockets in the oil pump body (10) .
Place oil pump drive shaft (6) and oil pump idler shaft (7) in oil pump body (10) . Ensure that the gears are 0.14 mm to 0.16 (0.0055 inch to 0.0063)below the surface of the housing.
Put clean engine oil on the bearings in cover (4) . Put clean engine oil on the top surface of the gears in oil pump body (10) .
Put cover (4) in position on oil pump body (10) .
Illustration 4 g00551225
Ensure that cover (4) is against the oil pump body. Ensure that all of the O-ring seals are in place. Install the bolts that hold cover (4) to the oil pump body.
Ensure that plug (11) is installed in the oil pump idler shaft.
Ensure that plug (12) is installed in the front cover.
Illustration 5 g00551226
Note: Ensure that dowel (13) is installed at the location that is shown in Illustration 5 for a SAE standard rotation engine.
Install dowel (13) to a height of 8 1 mm (0.32 0.04 inch).
Ensure that two plugs (15) are installed.
Install Tooling (A) .
Install the gear and washer (14) . Install the bolt.
Strike the head of the bolt with a hammer. Tighten the bolt again.
Illustration 6 g00551227
Ensure that plug (16) is installed in the oil pump drive shaft.
Ensure that hollow dowel (17) is installed to a height of 4.0 0.5 mm (0.16 0.02 inch).
Place the O-ring seal on the dowel. Put a coat of clean engine oil on the seal.
Install the O-ring seals on cover (18) and cover (19) . Put a coat of clean engine oil on the seals.
Install cover (18) and cover (19) .
Rotate the pump by hand. The pump must rotate freely. If the pump does not rotate freely, disassemble the pump in order to determine the cause.End By: Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts applique JOHNSON:

0323782
 
0323782 APPLIQUE,Lever
100ML79S, 115ML79R, 140ML79R, 150TL79C, 175TL79R, 200TL79A, 235TL70A, 50R79C, 55E79C, 70EL79R, 75ELR79R, 85ML79R
0389598
 
0389598 APPLIQUE, 100 hp
100ML79S, 115ML79R, 140ML79R, 85ML79R
0323970
 
0323970 APPLIQUE, Starboard
100ML79S, 115ML79R, 140ML79R, 85ML79R
0323969
 
0323969 APPLIQUE, Port
100ML79S, 115ML79R, 140ML79R, 85ML79R
0323965
 
0323965 APPLIQUE, Rear
100ML79S, 115ML79R, 140ML79R, 85ML79R, J100MLCSC, J115MLCSA, J140MLCSA, J85MLCSA
Back to top