0315642 BAND, Seal valve housing JOHNSON
100ESL71A, 100ESL72R, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 85EL76D, 85EL77S, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M, 85ESL74B, 85ESL75E
BAND
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARCASE » 0315642
115EL77S, 115ETL77 1977
115ESL69E, 115ESL69S 1969
115ESL70D 1970
115ESL73M 1973
115ESL74B, 115ETL74B 1974
115ESL75E, 115ETL75E 1975
125ESL71C 1971
125ESL72R 1972
135ESL73M 1973
135ESL74B, 135ETL74B 1974
135ESL75E, 135ETL75E 1975
85EL76D, 85EL76G, 85ETLR76D, 85ETLR76G 1976
85EL77S, 85ETLR77S 1977
85ESL69E, 85ESL69M, 85ESL69S 1969
85ESL70B, 85ESL70D 1970
85ESL71A, 85ESL71H 1971
85ESL72R 1972
85ESL73M 1973
85ESL74B 1974
85ESL75E 1975
Information:
To prevent damage to the inlet & exhaust valves, an adjustment must be made to the inlet & exhaust valve clearance setting. Loosen the nuts on each rocker arm and move the adjustment screw on each rocker arm away from the bridge as far as possible.
1. Put engine in position on Tool (A) and turn the engine over on its side. Make sure the blocks that are used as support for the top of the engine are against the cylinder head only and not against the exhaust manifold or valve cover bases. 2. Loosen the nuts that hold each connecting rod bearing caps (1) in position. Turn the crankshaft if necessary to loosen all the nuts. Make sure the nuts are still tight enough to hold the bearing caps in place when the crankshaft is turned. 3. Turn the crankshaft so that the "V" mark on the crankshaft gear is in alignment with "V" mark (3) on the idler gear.4. Remove the bearing caps that hold the connecting rods in position against the crankshaft. 5. Remove bearings (4) from each bearing cap. Make sure that each bearing is kept with the bearing cap it is removed from for correct installation purposes. 6. Remove crankshaft main bearing caps No.2 through No. 6 for the 3412 Engine and bearing caps No.2 through No.4 for the 3408 Engine.7. Push the pistons as far away as possible from the crankshaft. 8. Remove bearing (6) from each crankshaft main bearing cap. Make sure that each bearing is kept with the crankshaft main bearing cap it is removed from for correct installation purposes. 9. Remove two thrust-plates (7) from the center main bearings. 10. Fasten Tool (B) and a hoist to the crankshaft as shown.11. Remove the No. 1 and No. 7 crankshaft main bearing caps for the 3412 Engine. Remove the crankshaft main bearing caps No.1 and No.5 for the 3408 Engine.12. Use Tool (B) and a hoist to remove crankshaft (8) from the cylinder block. The weight of the crankshaft for a 3412 Engine is approximately 181 kg (400 lb). The weight of the crankshaft for the 3408 Engine is approximately 143 kg (315 lb). 13. Use Tool (C) to remove gear (9) from the crankshaft. Use Tool (D) to remove the dowel that is under the gear if a replacement is necessary. 14. Use Tool (E) to remove pin (10) from the crankshaft if a replacement is necessary. 15. Put identification on bearings (11) and (12) as to their location on the cylinder block or connecting rod. Remove bearings (11) and (12).Install Crankshaft
Do not put oil