0384871 JOHNSON TERMINAL ASSY., Negative

Start By:a. remove valve covers 1. Use Tool (A) to disconnect three adapters (4) and (5).2. Remove three nuts (2) and locknuts (3).3. Remove three fuel lines (1). 4. Remove the cover from the flywheel housing and install Tool (B). Use Tool (B) to turn the crankshaft to release any pressure against the rocker arms.5. Use Tool (C) to move the rocker arms away from push rods (6) far enough so the push rods can be removed. 6. Put identification on valve bridges (9) as to their location for correct installation. Remove valve bridges (9).7. Remove bolts (7) and rocker shaft assembly (8).Install Rocker Shaft Assembly
1. Put rocker shaft assembly (8) in position.2. Put clean engine oil on bolts (7). Install three bolts (7) for the 3412 Marine Engine and four bolts (7) for the 3408 Marine Engine.
Tightening Sequence for 3408 Rocker Shaft Assembly3. Hold the rocker shaft assembly in position. Install bolts (7) and use the following procedure to tighten the bolts.a. Tighten bolts (7) in numerical sequence as shown in the illustration above to 271 27 N m (200 20 lb ft).b. Tighten bolts (7) again in numerical sequence to 447 20 N m (330 15 lb ft).c. Repeat Step 3b again to make sure all the bolts are tightened to the correct torque.
Tightening Sequence for 3412 Rocker Shaft Assembly4. Use the following procedure to tighten bolts (7). After the installation of bolts (7). Make sure the tightening sequence in the illustration above is followed.a. Tighten bolts (10) through (15) in numerical sequence to 280 27 N m (210 20 lb ft).b. Tighten bolts (10) through (15) in numerical sequence to 440 20 N m (320 15 lb ft).c. Do Step 4b again to make sure all the bolts are tightened to the correct torque.5. Put clean engine oil on the valve bridge dowels. Install valve bridges (9) in their original positions on the engine. 6. Use Tool (A) to make sure there will be no pressure against push rod (16) and rocker arm (17). Use Tool (B) to pull rocker arm (17) away from push rod (16). Put push rod (16) in position under the rocker arm. If the rocker arm can not be moved enough to put the push rod in position, turn the crankshaft with Tool (A).7. Make an adjustment of the valves to have a clearance of .038 mm (.0150 in) for intake and 0.76 mm (.030 in) for exhaust. See the topic, "Valve Clearance Setting" in System Operation, Testing & Adjusting Manual, SENR5517. 8. Make sure the O-ring seal is in position on the adapter. Put clean engine oil on the O-ring seal. Put adapters (4) and (5) with fuel lines (1) in position in the valve cover base.9. Install locknuts (3) and nut (2). Tighten locknuts (3) to a torque of 30 7 N m (22 5 lb ft). Tighten nut (2) to a torque of 41 7 N m (30 5 lb ft).10. Use Tool (C) to tighten adapters (4) and (5) to a torque of 41 7 N m (30 5 lb ft).End By:a. install valve coversDisassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly 1. Remove retainer (3), washers (2) and rocker arm (4) from the rocker shaft assembly.2. Make sure dowel (1) is free of oil. 3. Put Tool (A) in position on dowel (1). Pull rocker arm (6) away from bracket assembly (5). Remove the dowel with Tool (A). Remove bracket assembly (5). 4. Remove rocker arms (9), spring (8) and brackets (7). Use Tool (A) to remove the dowel that holds bracket assembly (6) on the rocker shaft. 5. Remove nuts (10) and screws (11) from the rocker arms if a replacement is necessary. 6. Remove plug (12) from rocker shaft (13) if a replacement is necessary.Assemble Rocker Shaft Assembly
Make sure all the parts of the rocker shaft assembly are clean before assembly. 1. Install plug (1) in the end of rocker shaft (2). Install the plug to a depth of 12.7 1.0 mm (.50 .04 in) from the end of the shaft.2. Do Step 1 again for the plug in the other end of the shaft. 3. Install screws (4) and nuts (3) on each of the rocker arms. 4. Put the retainer, the original washers and rocker arm (8) in position on the rocker shaft. Put bracket assembly (5) in position on the shaft so that the hole in the bracket assembly is in alignment with the larger hole in the shaft.5. Install the dowel that holds the bracket assembly in place.6. Install the rest of the rocker arms, springs (9) and brackets (6). Push rocker arm (7) to the left of the large hole (10). Install the other bracket assembly. Make sure hole (12) in the bracket assembly is in alignment with hole (10).7. Install dowel (11) through the bracket assembly and into hole (10). 8. Dowel (11) must be installed so that dimension (X) is 12.7 1.0 mm (.50 .04 in). 9. Install the last rocker arm (13), the original washers (14) and retainer (15). 10. Use feeler gauge (16) to check the clearance between the rocker arm and the washers. Add or subtract washers as necessary until the clearance is 0.30 to 1.40 mm (.012 to .055 in). Check the clearance at the other end of the rocker shaft assembly.End By:a. install rocker shaft assembly