5030268 JOHNSON BEARING HOUSING, Prop shaft, Jo.


5030268 BEARING HOUSING, Prop shaft, Jo. JOHNSON J5RECS BEARING
5030268 BEARING HOUSING, Prop shaft, Jo. JOHNSON
Rating:
53

Buy BEARING HOUSING, Prop shaft, Jo. 5030268 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$16.88
 

07-06-2023

-: -
MICHELIN Serpentine Drive Belt SMAMV3PK680S
Optimize Costs and Reduce CO2 Emissions - Our serpentine drive belts are high-performance components able to withstand difficult engine environments with high speed, high temperatures, and wet conditions, making them especially durable and wear-resistant. Increased flexibility and reduced weight optimize costs and reduce CO2 emissions. || Built-In Tension and Product Warranty - MICHELIN belts are available with polyamide cord, which allows the belt to automatically maintain the right belt tension over time. This provides compact, low-noise drive solutions with low maintenance and higher cost-effectiveness. Also includes a one-year product warranty for defects in material and workmanship under normal use and service. || This product is designed to fit specific vehicles per the OEM design and requirements.  Please confirm with your vehicles owner’s manual or OEM specification to ensure correct part specification before purchasing this component.  Note that engine size, accessory options and other options can impact the product size and design.  If further assistance is needed contact the seller directly for additional product information and availability. || Replaces 5030268, 3PK0680, K030268 OE part numbers. || 3 Ribs 26.8 in. x 0.4 in. - 680 mm x 10.16 mm
$32.83
 

28-06-2021
0.88[0.00] Pounds
-: -
Dayco 5030268 Serpentine Belt Equivalent 268K3, 3 Rib Poly-V Belt, 11 Pack
YOU ARE ORDERING A DAYCO EQUAL REPLACEMENT BELT MADE TO THE OEM SPECIFICATIONS MANUFACTURED BY POWERDRIVE. YOU WILL NOT RECEIVE A GENUINE OEM DAYCO BELT WHEN ORDERING THIS PART. || All belts meet or exceed SAE J1459, SAE J2432, and SAE J1596 specifications || Interchangeable to NAPA, Carquest, Dayco, Gates, Goodyear and all OEM car manufacturers || Multiple micro-v-ribs for any size pulley width || Oil Resistant || Heat Resistant || Abrasion Resistant || Made from Polyester-Rubber Compound for wear-resistant and to the tightest automotive industry tolerances.
$5.72
 

18-09-2021
0.1875[0.00] Pounds
-: -
K030267 Serpentine DAYTONA belt OEM Quality 3PK685 5030268 4030267 268K3 K30267 3PK0680
OEM Manufacturer Quality by Daytona Rubber Company || Meet and Exceed SAE quality Specifications || Constructed with fiber cords to increase strength and provide resistance to cracking and wear || Effective Length (in) 26.80 Effective Length (mm) 681 Number of Ribs 3 Outside Circumference (in) 27.36 Outside Circumference (mm) 695 Top Width (in) .42 Top Width (mm) 11
Number on catalog scheme: 29
 

Compatible models:

J5RECS   JOHNSON

BRP JOHNSON entire parts catalog list:

J5RECS, J5RLECS 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-4653 Counterweight Tool 1
B 4C-5597 Anti-Seize Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02176197
Ensure that turbocharger (4) is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If any part of the turbocharger is worn or damaged, the complete turbocharger must be replaced.
Test wastegate actuator (24) for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If any part of the wastegate actuator is worn or damaged, the complete turbocharger must be replaced.
Illustration 2 g02175963
Clean the gasket surface of exhaust manifold (20). If necessary, install studs (23) to turbocharger (4). Tighten the studs to a torque of 18 N m (160 lb in).
Install a new gasket (22) to turbocharger (4).
Position turbocharger (4) onto the exhaust manifold and install nuts (21) finger tight. The nuts (21) should not constrain the turbocharger and prevent Tooling (A) from correctly positioning the turbocharger onto the exhaust manifold.
Use Tooling (A) to align turbocharger (4). Note: Ensure that the turbocharger is correctly oriented.
Tighten nuts (21) to a torque of 44 N m (32 lb ft).
Remove Tooling (A) from turbocharger (4).
Illustration 3 g02176198
Illustration 4 g02175962
Remove plugs and caps from tube assemblies. Ensure that tube assembly (19) and tube assembly (15) are clean and free from damage. Replace any damaged components.
Position a new gasket (17) (not shown) onto tube assembly (19).
Install bolts (18) to tube assembly (19). Tighten the bolt to a torque of 9 N m (80 lb in).
Remove the plug from oil inlet port (25). Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Install a new sealing washer (16) to banjo bolt (14). Install banjo bolt (14) to tube assembly (15) and install remaining sealing washers (16) to banjo bolt (14).
Tighten banjo bolt (14) to a torque of 20 N m (177 lb in).
Illustration 5 g02175961
Use Tooling (B) to lubricate the allen head bolt for V-band clamp (6). Position V-band clamp (6) onto air duct (13).
Position hose assembly (12) and air duct (13) onto the outlet of turbocharger (10) and turbocharger (4). Ensure that the V-band clamp (6) is seated correctly onto the turbochargers.
Tighten the allen head bolt for V-band clamp (6) to a torque of 12 N m (106 lb in).
Tighten hose clamps (11) to a torque of 6 N m (53 lb in).
Use Tooling (B) to lubricate the allen head bolt for V-band clamp (9). Position V-band clamp (9) onto turbocharger (10).
Use Tooling (B) to lubricate the allen head bolt for V-band clamp (3). Position V-band clamp (3) onto elbow (1).
Position elbow (1) onto turbocharger (10) and turbocharger (4).
Tighten allen head bolt for V-band clamp (3) and V-band clamp (9) finger tight. Ensure that the V-band clamps are seated correctly onto the turbochargers.
Tighten allen head bolt for V-band clamp (3) and V-band clamp (9) to a torque of 12 N m (106 lb in).
Connect hose assembly (2) to the wastegate actuator. Note: Ensure that the clip for hose assembly is correctly positioned.
Connect hose assembly (7) to the connection in outlet of turbocharger (4). Note: Ensure that the clip for hose assembly is correctly positioned.
Install bolt (8) to clip for tube assembly. Tighten the bolt to a torque of 22 N m (195 lb in).
Connect hose assembly to air outlet (5) of turbocharger (4). Tighten the hose clamps securely.


Parts bearing JOHNSON:

5030100
 
5030100 BEARING, Wrist pin
J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030098
 
5030098 BEARING, Crankshaft
J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030099
 
5030099 BEARING, Gear
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J5RECS, J5REEC, J5RLSIM, J5RLSSA, J6R4SDC, J6R4SOS, J6R4SUR
5030097
 
5030097 BEARING, Propeller shaft
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J5RECS, J5REEC, J5RLSIM, J5RLSSA, J6R4SDC, J6R4SOS, J6R4SUR
Back to top