5031323 BEARING SET, Crankshaft - No paint JOHNSON
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
BEARING
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- CRANKSHAFT & PISTONS » 5031323
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003
Information:
Table 1
Diagnostic Trouble Codes for the ARD Nozzle    
CDL Code     Description     Notes    
E1070-1     Aftertreatment Fuel Injector #1 not responding     The fuel flow to the Aftertreatment Regeneration Device (ARD) fuel nozzle is restricted.    The ARD nozzle can become plugged with carbon or with debris. The Electronic Control Module (ECM) periodically tests the condition of the nozzle. The engine is equipped with a system that cleans the nozzle. A restriction in a filter connector for the ARD combustion head can also set this code.Electric Heating Element - The ARD combustion head contains an electric heating element. The heating element operates periodically in order to clean the nozzle.Features on the Electronic Service ToolARD Nozzle Heater Test - This process activates the output for the heated nozzle in order to test the nozzle heater circuit. The output only remains activated when selected on the electronic service tool. The heat cycle stops if the engine is stopped.ARD Fuel Nozzle Heater Override - This process activates the output for the heated nozzle in order to clean the nozzle. The output remains activated for approximately 1 hour. The heat cycle stops if the engine is stopped. The heat cycle continues when the engine is started. Active regenerations will not occur until the heat cycle is complete.ARD Ignition Test - The test operates the ARD for approximately 5 minutes while the engine is running. The test determines if the ARD can generate heat. If the ARD cannot generate heat, a diagnostic code is activated. The code indicates the specific problem with the ARD.Test Step 1. Check for Active or Recently Logged Diagnostic Codes
Turn the keyswitch to the ON position.
Establish communication between the electronic service tool and the ECM. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
The ignition system may cause an electrical shock hazard, which may cause personal injury or death. Avoid contacting the ignition system components and the ignition system wiring during operation.
Use the electronic service tool in order to perform the "ARD Ignition Test".Note: The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, use the electronic service tool to perform a Manual DPF Regeneration.Results:
The "ARD Ignition Test" was successful and no codes were logged. - Return the unit to service.STOP
The "ARD Ignition Test" was not successful and an E1070-1 diagnostic code was logged. - Proceed to Test Step 2.
The "ARD Ignition Test" was not successful and another diagnostic code was logged. - Repair: Troubleshoot the other diagnostic codes. Refer to Troubleshooting, "Diagnostic Trouble Codes".STOPTest Step 2. Check the Current Flow Through the ARD Nozzle Heater
Turn the keyswitch to the OFF position.
Illustration 1 g02231813
Typical view of the ARD combustion head (1) Insulated part of the heater wire
Connect a suitable clamp-ammeter around the insulated part of the heater wire (1) .
Turn the keyswitch to the ON position.
Do not energize the heater for more than 30 seconds. If the heater is energized more than 30 seconds, damage to the heater can occur. Allow the heating element to cool for 2 minutes between power cycles.
Use the "ARD Nozzle Heater Test" in the electronic service tool to switch on the ARD nozzle heater.
Record the current reading on the ammeter.
Use the "Aftertreatment #1 Fuel Injector #1 Heater Override" in the electronic service tool to switch off the ARD nozzle heater.Expected Result:The ammeter should read at least 3.5 Amps.Results:
OK - The current is correct for the system. The ARD nozzle heater is operating correctly. Proceed to Test Step 3.
Not OK - The current is below the expected level for the system.Repair: Diagnose and repair the fault with the ARD nozzle heater circuit. Refer to Troubleshooting, "ARD Nozzle Heater - Test". When the nozzle heater circuit has been repaired, proceed to Test Step 4.Test Step 3. Replace the ARD Filter Connector in the ARD Combustion Head
Illustration 2 g02231814
Typical view of the ARD combustion head (2) Pilot filter connector
Replace pilot filter connector (2) in the ARD combustion head
Clear all diagnostic codes.
The ignition system may cause an electrical shock hazard, which may cause personal injury or death. Avoid contacting the ignition system components and the ignition system wiring during operation.
Use the electronic service tool in order to perform the "ARD Ignition Test".Note: The ARD Ignition Test cannot be performed if the DPF soot loading is above 80%. When the DPF soot loading is above 80%, use the electronic service tool to perform a Manual DPF Regeneration.Results:
The "ARD Ignition Test" was successful and no codes were logged. - Return the unit to service.STOP
The "ARD Ignition Test" was not successful and an E1070-1 diagnostic code was logged. - Proceed to Test Step 5.
The "ARD Ignition Test" was not successful and another diagnostic code was logged. - Repair: Troubleshoot the other diagnostic codes. Refer to Troubleshooting, "Diagnostic Trouble Codes".STOPTest Step 4. Perform an ARD Nozzle Heat Cycle
Start the engine.Note: The ECM must have an engine speed signal to initiate the ARD nozzle heater cycle.
Initiate the cycle for the ARD nozzle heater. The cycle for the ARD nozzle heater will cycle the nozzle ON and OFF for an hour in order to clean the nozzle.
The ignition system may cause an electrical shock hazard, which may cause personal injury or death. Avoid contacting the ignition system components and the ignition system wiring during operation.
When the "ARD Nozzle Heat Cycle" is complete, use the electronic service tool to perform an "ARD Ignition Test".Results:
The "ARD Ignition Test" was successful and no codes were logged. - Return the unit to service.STOP
The "ARD Ignition Test" was not successful and an E1070-1 diagnostic code was logged. - Proceed to Test Step 5.
The "ARD Ignition Test" was
Parts bearing JOHNSON:
5032828
5032828 BEARING, CONNECTING ROD
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031324
5031324 BEARING SET, Crankshaft - Yellow
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031325
5031325 BEARING SET, Crankshaft - Blue
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031321
5031321 BEARING SET, Crankshaft - Green
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031322
5031322 BEARING SET, Crankshaft - Black
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031320
5031320 BEARING SET, THRUST
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031256
5031256 *BEARING, PINION
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031259
5031259 *BEARING
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC