5031389 JOHNSON BODY, THROTTLE W/CTP SWITCH


5031389 BODY, THROTTLE W/CTP SWITCH JOHNSON BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC BODY
5031389 BODY, THROTTLE W/CTP SWITCH JOHNSON
Rating:
8

Buy BODY, THROTTLE W/CTP SWITCH 5031389 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£39.83
 

18-09-2017
4.41[1.80] pounds
Connected : Connected Essentials
Connected Essentials 5031389 Tailored Heavy Duty Custom Fit Car Mats, for Nissan Qashqai 2 (2007-2010), Black with Red Trim, Premium
Complete set of 6 tailored custom fit car mats - designed and manufactured specifically for Nissan Qashqai 2 (2007-2010)||Supplied with clips (as applicable) for security||Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear||Manufactured from 650gram automotive quality carpet - for strength and durability||Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 2
 

BRP JOHNSON entire parts catalog list:

BJ40PL4SDR, J40PL4SDE 2006
BJ40PL4SOC, J40PL4SOB 2005
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7572     Link Bracket     3    
ZZ     9L-8493     Cap (7/16 JIC)     1    
9S-5518 Plug (7/16 JIC)     1    
6V-9507 Face Seal Plug (9/16 -18 THD)     1    
6V-9828 Cap As (9/16 - 18 THD)     1    
6V-9510 Face Seal Plug (1 - 14 THD)     2    
6V-9831 Cap As (1 - 14 THD)     2    
6V-9511 Face Seal Plug (1 13/16 - 12 THD)     2    
6V-9832 Cap As (1 13/16 - 12 THD)     2    
9U-7074 Caps     2    
9U-7087 Caps     4    Start By:
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove filler cap slowly to relieve pressure only when engine is stopped and radiator cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Conditioner contains alkali. Avoid contact with skin and eyes.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.Note: Put identification marks on all lines, hoses, wires, and tubes for installation purposes. Plug all lines, hoses and tubes. This helps prevent fluid loss and contamination of the fluid systems.
Drain the coolant from the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g00911221
Remove pin (1) .
Illustration 2 g00911228
Remove clip (2). Remove strut (3). Remove clamp (4). Remove the hose.
Illustration 3 g01028506
Disconnect tube assemblies (5). Loosen clamps (6). Disconnect hoses (7). Disconnect hose assemblies (8) .
Illustration 4 g00911306
Loosen clamp (9). Disconnect hose (10) .
Illustration 5 g00911318
Attach a suitable lifting device and Tooling (A) to the radiator assembly.
Illustration 6 g00911317
Support the r


Back to top