0437122 JOHNSON BRACKET & STUD ASSY., Belt cover


0437122 BRACKET & STUD ASSY., Belt cover JOHNSON BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, J10FEXEO, J15DLEOC BRACKET
0437122 BRACKET & STUD ASSY., Belt cover JOHNSON
Rating:
38

Buy BRACKET & STUD ASSY., Belt cover 0437122 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$267.23
 

22-12-2022

-: -
Replacement For EZGO/CUSHMAN/TEXTRON 0437-122 Battery
Replacement For EZGO / CUSHMAN / TEXTRON 0437-122 || Unit per sale:1
$286.85
 

24-07-2024

US: Technical Precision
Technical Precision Replacement for EZGO/Cushman/TEXTRON 0437-122
Technical Precision Replacement For EZGO / CUSHMAN / TEXTRON 0437-122 || Unit per sale:1
Number on catalog scheme: 24
 

BRP JOHNSON entire parts catalog list:

BJ10FDLECM, J10FEXECM, J10FRECM, J10FRELECM, J10FRLECM 1998
BJ10FDLEDR, BJ10FPXEDC, BJ10FRELDR, J10FEXEDR, J10FREDR, J10FRELEDR, J10FRLEDR 1996
BJ10FDLEUA, BJ10FPXEUR, BJ10FRELUA, J10FEXEUA, J10FRELEUA, J10FREUA, J10FRLEUA 1997
BJ15FAEDR, BJ15FDLEDR, BJ15FKEDR, BJ15FREDR, BJ15FRELEDR, BJ15FWEDC, BJ15FWLEDC, J15FKEDR, J15FREDR, J15FRELEDR, J15FRLEDR 1996
BJ15FAEUA, BJ15FDLEUA, BJ15FKEUA, BJ15FRELUA, BJ15FREUA, BJ15FWEUR, BJ15FWLEUR, J15FKEUA, J15FRELEUA, J15FREUA, J15FRLEUA 1997
BJ15FDLECM, BJ15FWECA, BJ15FWLECA, J15FRECM, J15FRELECM, J15FRLECM 1998
J10FEXEO, J10FRELEOC, J10FREOC, J10FRLEO 1995
J15DLEOC, J15FREOC, J15FRLEOC, J15KEOC 1995

Information:

start by:a) remove fuel injection pump housing and governorb) remove adapter housing 1. Put the fuel injection pump housing and governor in position on tool (A).2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing. 3. Remove governor housing (2).4. Remove two bolts (3) from the cover. Remove cover (4) from over the torque spring. 5. Remove spring (7), wave washer (6) and guide (5) from the governor housing.6. Remove gasket (8) from the governor housing. 7. Remove bolt (11) and nut (9) from the torque spring (10). Remove the torque spring.8. Remove pin (12) from the hole in the fuel injection pump housing. 9. Remove seat (15) and over fueling spring (16) from the shaft.10. Pull shaft (13) up and remove lever (14). 11. Remove riser (follower) (18) from the shaft.12. Remove ring and lever (17) from the dowel. 13. Remove cover (19) with tool (B). Tool (B) can cause damage to cover. Always inspect the cover for damage and install a new cover if needed. 14. Install timing pin (20) to hold the camshaft from turning.15. Remove three bolts (21) that hold the flyweight assembly in position.16. Remove flyweight assembly (22).17. Remove the timing pin from the fuel injection pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before installing the flyweight assembly.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to overspeed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing. 15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by:a) install adapter housingb) install fuel injection pump housing and governor


Parts bracket JOHNSON:

0341271
 
0341271 BRACKET, Solenoid to cylinder head
BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, J10FEXEO, J15DLEOC
0436605
 
0436605 BRACKET & STUD
BJ10FDLEDR, BJ15FAEDR, J10FEXEO, J15DLEOC
0341301
 
0341301 BRACKET, Starter motor
BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, J10FEXEO, J15DLEOC
0343450
 
0343450 BRACKET, Rear
BJ10FDLECM, BJ10FDLEUA, BJ15FAEUA, BJ15FDLECM
Back to top