0446344 JOHNSON BRACKET, Solenoid


0446344 BRACKET, Solenoid JOHNSON BJ10FAEDC, BJ10FAEUR, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA BRACKET
0446344 BRACKET, Solenoid JOHNSON
Rating:
8

Buy BRACKET, Solenoid 0446344 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

BRP JOHNSON entire parts catalog list:

BJ10FAEDC, BJ10FCLEDC, BJ10FWEDC, BJ10FWLEDC, HJ10FDEDC, HJ10FDLEDC, HJ10FELEDC, HJ10FTEDC, HJ10FTLEDC 1996
BJ10FAEUR, BJ10FCLEUR, BJ10FWEUR, BJ10FWLEUR, HJ10FELEUR, HJ10FOEUR, HJ10FOLEUR, HJ10FTEUR, HJ10FTLEUR 1997
BJ8FRBECA, BJ8FRBLECA, J8FRECA, J8FRLECA, J8FRXECA 1998
BJ8FRBEDC, BJ8FRBLEDC, BJ8FRBXEDC, HJ8FREDC, HJ8FRLEDC, J8FREDC, J8FRXEDC 1996
BJ8FRBEUR, BJ8FRBLEUR, BJ8FRBXEUR, HJ8FREUR, HJ8FRLEUR, J8FREUR, J8FRXEUR 1997
HJ10FELECA, J10FOECA, J10FOLECA 1998

Information:


Illustration 1 g01208146
Schematic diagram for the electrical power supplyTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01208154
Typical left side view (1) J1/P1 ECM connectors
Illustration 3 g01208163
P1 terminals that are associated with the electrical power supply (P1-48) +Battery (P1-52) +Battery (P1-53) +Battery (P1-61) −Battery (P1-63) −Battery (P1-65) −Battery (P1-70) Keyswitch
Thoroughly inspect connectors (1) and (2). Inspect the connections for the battery and the connections to the keyswitch. Refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect".
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the electrical power supply.
Check the allen head screw on each ECM connector for the proper torque. Refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Also, check the harness and wiring for abrasions and for pinch points from the keyswitch to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are okay. Proceed to Test Step 2.
Not OK - There is a problem with the connectors or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check the Battery Voltage at the ECM
Disconnect the J1/P1 ECM connector.
Restore the electrical power to the ECM.
Measure the voltage between P1-52 (Unswitched Positive Battery) and P1-63 (Negative Battery).
Measure the voltage between P1-48 (Unswitched Positive Battery) and P1-61 (Negative Battery).
Measure the voltage between P1-53 (Unswitched Positive Battery) and P1-65 (Negative Battery).
Measure the voltage between P1-70 (Keyswitch) and P1-63 (Negative Battery).Expected Result:The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 volt system and between 22.0 VDC and 27.0 VDC for a 24 volt system with no suspected intermittent problems at this time.Results:
OK - The ECM is receiving the correct voltage. Repair: If an intermittent condition is suspected, refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect".STOP
Battery voltage is out of range - Proceed to Test Step 3.
Keyswitch voltage out of range - Repair: Trace the wiring for the keyswitch from the ECM through the keyswitch circuit to the batteries. Find the problem and repair the problem. Check the circuit protection for the circuit and for the wiring.Verify that the repairs eliminate the problem.STOPTest Step 3. Check the Batteries
Measure the no-load battery voltage at the battery posts.
Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure".Expected Result:The batteries pass the load test. The measured voltage is the minimum specification for a 12V or 24V system.Results:
OK - The batteries are OK.Repair: Check the wiring between the batteries and the ECM for shorts.Check the connectors between the batteries and the ECM for moisture and/or corrosion.Repair the wiring and/or the connectors.Verify that the repair eliminates the problem.STOP
Not OK - The battery voltage is low or the battery did not pass the load test.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOP


Parts bracket JOHNSON:

0437120
 
0437120 BRACKET ASSY.
BJ10FAEDC, BJ10FAEUR, BJ5FRBECC, BJ5FRBEUS, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS, J8R4SRC, J8R4STS
0446320
 
0446320 BRACKET, Power pack
BJ10FAEDC, BJ10FAEUR, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA
0446106
 
0446106 BRACKET, Support
BJ10FAEDC, BJ10FAEUR, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, J8R4SRC, J8R4STS
0445090
 
0445090 BRACKET ASSY., Shift
BJ10FAEDC, BJ10FAEUR, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, J8R4SRC, J8R4STS
Back to top